F5 BIG-IP 8950 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 56

background image

If the system does not boot after you power on the DC power source, press the Check button on the
LCD panel to begin booting the system.

About the fan tray

The BIG-IP

®

8950 platform has a removable fan tray that is designed to maintain airflow throughout the

chassis. You can change or replace the fan tray as part of the routine maintenance of the unit, or in the event
of a fan failure. The fans in the fan tray run constantly while the unit is on. Over time, the fans can wear
out, requiring you to replace the fan tray.

Important: This product is sensitive to electrostatic discharge (ESD). F5 Networks recommends that
you use proper ESD grounding procedures and equipment when you install or maintain the unit.

Figure 9: An example of a fan tray in a platform

Replacing the fan tray

You do not need special tools to replace the fan tray. You do not need to power down the unit when replacing
the fan tray; however, F5 Networks highly recommends that you do not leave the unit operating without a
fan tray for longer than 30 seconds.

Caution: Operating the unit without a fan tray for more than 30 seconds may cause permanent damage.

1. Stand at the back of the platform and locate the ejector handle on the fan tray.

2. Loosen the fan tray screws by turning them counterclockwise with a Phillips screwdriver, if necessary.

Note: The screws that hold the ejector handle in place are captive and cannot be removed from
the assembly.

3. Grasp the ejector handle and rotate it downward to eject the fan tray from the system.

4. Remove the fan tray from the system by pulling straight toward you.

5. Ensure that the handle on the new fan tray is in the down position and slide the fan tray into the fan tray

slot until the latch engages.

6. Rotate the handle upward to fully seat the fan tray.

7. Tighten the screws into place.

The fan tray is connected to the system when you tighten the screws completely. Once seated, the fan
tray automatically powers up and begins circulating air through the chassis.

34

Platform Maintenance

«
...
32
33
34
35
36
...
»

Содержание BIG-IP 8950

























































Отзывы:

Нет отзывов

Похожие инструкции для BIG-IP 8950

eServer BladeCenter JS20 Type 8842

Бренд: IBM Страницы: 150

x3655 - System - 7985

Бренд: IBM Страницы: 118

Бренд: SafeNet Страницы: 109

totalstorage 200

Бренд: IBM Страницы: 180

NovaScale T820 F2

Бренд: Bull Страницы: 34

Бренд: Patton electronics Страницы: 121

Бренд: Olive Страницы: 19

Бренд: Xerox Страницы: 2

PRIMERGY TX140 S2

Бренд: Fujitsu Страницы: 86

PRIMERGY TX150 S3

Бренд: Fujitsu Страницы: 95

PRIMERGY TX150 S6

Бренд: Fujitsu Страницы: 118

Бренд: Fujitsu Страницы: 305

PRIMERGY TX150 S6

Бренд: Fujitsu Страницы: 127

PRIMERGY TX140 S2

Бренд: Fujitsu Страницы: 332

PRIMERGY TX150 S4

Бренд: Fujitsu Страницы: 97

PRIMERGY TX150 S7

Бренд: Fujitsu Страницы: 120

PRIMERGY TX140 S1p

Бренд: Fujitsu Страницы: 9

DIGI CONNECT ES

Бренд: Digi Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды