Ezy-Lift 2000 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 21

Ezy-Lift 2000 Скачать руководство пользователя страница 2

2

2

FLAT BED EZY-LIFT 2000

TABLE OF CONTENTS

SAFETY

Caution: Read this entire procedure before beginning work.  Always wear safety glasses and use care when work-
ing with power tools.

Safety is a primary concern in the design and manufacturing of our products.  But remember that all efforts to pro-
vide safe equipment can be totally negated by a single careless act of an installer or operator.

Accident prevention and safety are dependent upon the awareness and proper training of the personnel who operate
and maintain this equipment.  The best safety device is a careful and informed owner/operator.

Product Specifications

2

Trouble Shooting

18

Installation

3

Warranty

18

Know Your EZY LIFT

12

Hydraulic Diagram

19

Operation

14

Electrical Diagrams

20

The Flat Bed Ezy-Lift Model 2000 8.0 lifting system has a rated lift capacity of 2000 pounds.

Overloading the vehicle can cause potential safety hazards! Carefully read all the installation and operating in-
structions in this manual. Failure to follow safety precautions may result in accidents that may result in property
damage, serious injury or death.

Lifting Capacity

2,000 Lbs. for Flat Bed

Power Supply

12 V DC operation from vehicle battery, 150 amp fuse at vehicle battery

Hydraulic System

Single direction system with directional valve. Two 3” cylinders provide lift rotation.

Crane Winch

Designed for lifting with 159:1 gear ration, full load mechanical brake, 5:1 safety factor.

Cable

1/4” diameter 7x19 construction, galvanized, 15 ft in length with a 1.5 ton eye hoist hook
with latch.

Frame

11 gauge steel with powder black finish

Lifting Arm

High strength structural steel

Hub Bushings

Self lubricating bronze sleeve bushings

Remote Control

2 button 4 way control: up/down (Hoist), in/out (Boom) with 10 ft. long cord

Operating Time

From fully retracted to fully extended approximately 45 seconds

Hydraulic Fluid

ATF, OD18 or other clean hydraulic oil with a viscosity of 150 to 360 SUS at 38° C
(100° F)

Operating Temp.

Range between -20°F (-29°C) to 150°F (66°C)

System Weight

320 Pounds

Load Clearance

Boom up perpendicular to bed, from winch hook to bed 90 inches

Warranty

One Year

Product Specifications

«
1
2
3
4
...
»

Содержание 2000






















Отзывы:

Нет отзывов