Extron electronics SF 8CT SUB Скачать руководство пользователя страница 14

Страница: 14 / 14

68-3512-50 Rev. A

06 21

www.extron.com

All trademarks mentioned are the property of their respective owners.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide

on the Extron website.

Set the LPF selector switch to the appropriate setting using a small screwdriver. The default position is LPF enabled. Disable the LPF if
filtering is set on a device upstream of the speaker. The LPF is fixed at 120 Hz

Adjust the LF Selector Switch

120 Hz

OFF

Figure 20.

Setting the LPF selector switch

Install the grille. Position the grille so that it covers the baffle of the speaker. Six small magnets secure the grille in place.

Speaker Grille

Figure 21.

Installing the speaker grille

NOTE:

Specific test points can be used to troubleshoot speaker system problems. Should problems be encountered,

please see the

SF 8CT SUB User Guide.

Содержание SF 8CT SUB















Результаты поиска

Содержание SF 8CT SUB

Отзывы:

Похожие инструкции для SF 8CT SUB

Бренды по названию

Популярные бренды

Extron electronics SF 8CT SUB, Руководство по установке

Результаты поиска

Содержание SF 8CT SUB

Отзывы:

Похожие инструкции для SF 8CT SUB

Бренды по названию

Популярные бренды