Extron electronics MVX 128 Скачать руководство пользователя страница 52

Страница: 52 / 90

Operation, cont’d

MVX 128 A VGA Matrix Switchers • Operation

3-34

PRELIMINAR

Press and release an input or output button to exit the

Serial Port Confi guration

mode (fi gure 3-56).

ENTER PRESET VIEW

ESC

RGBHV AUDIO

CONTROL

I/O

All Control LEDs return to the unlit state.

Each I/O LED returns to its previous state.

Press and release an

input or output button.

Figure 3-56 — Exit

Serial Port Confi guration

mode

The switcher requires some time to save the new serial port settings. Wait at

least 5 minutes before removing power from the switcher or the settings may be
lost.

Rear Panel Operations

The rear panel has a Reset button that initiates two levels of matrix switcher resets.
Press and hold the button while the switcher is running or while you apply power
to the switcher for different reset levels.

Performing an absolute system reset from the rear panel

This function is identical to the front panel system reset (see

Performing a system

reset from the front panel

on page 3-32) without requiring you to power down the

switcher. This function is also identical to the

Esc

ZQQQ

SIS command, see

chapter 4,

Programmer’s Guide

). A system reset:

•

Clears all ties and presets

•

Clears all video and audio mutes

•

Sets all input audio levels to unity gain (+0 dB)

• Sets all output volume levels to 100% (0 dB of attenuation)

System reset does not replace any user-installed fi rmware.

Perform a system reset as follows:

Use an Extron Tweeker to press and

hold

the Reset button until the rear panel

Reset LED blinks three times (approximately 9 seconds) (fi gure 3-57).

RESET

Press and

hold

the Reset button.

Release, then

immediately

press and release again.

9 seconds

Reset LED blinks

three

times.

Reset LED blinks

four

times.

= Blink three times,

= blink four times

Figure 3-57 — System reset

Release the Reset button and then immediately press and release the Reset
button again.

The reset does not occur

if the second momentary press does

not occur within 1 second.

Содержание MVX 128



























































































Результаты поиска

Содержание MVX 128

Отзывы:

Похожие инструкции для MVX 128

Бренды по названию

Популярные бренды

Extron electronics MVX 128, Руководство пользователя

Результаты поиска

Содержание MVX 128

Отзывы:

Похожие инструкции для MVX 128

Бренды по названию

Популярные бренды