Extron electronics MVX 128 Скачать руководство пользователя страница 51

Страница: 51 / 90

3-33

MVX 128 A VGA Matrix Switchers • Operation

PRELIMINAR

Selecting the RS-232/RS-422 protocol and baud rate

The switcher can support either RS-232 or RS-422 serial communication protocol,
and operate at 9600, 19200, 38400, and 115200 baud rates. The settings of these
variables can be viewed and changed from the front panel.

View and confi gure the switcher’s serial communications settings as follows:

. To

enter

Serial Port Confi guration

mode, simultaneously press and

hold

all

Control buttons (Enter, Preset, View, and Esc) (fi gure 3-54).

ENTER PRESET VIEW

ESC

RGBHV AUDIO

CONTROL

ENTER PRESET VIEW

ESC

CONTROL

I/O

All Control LEDs light with one flashing.
Both I/O LEDs light with one flashing.
The flashing Control LED indicates the

baud rate

as follows:

Enter — 9600

Preset — 19200

View — 38400

Esc — 115200

The flashing I/O LED indicates the

protocol

as follows:

RGBHV — RS-232

Audio — RS-422

In this example, the port is set to RS-232 at 9600 baud.

Press and

hold

the Enter, Preset, View, and Esc buttons.

= Blinking LED

= Lit LED,

Figure 3-54 — RS-232/RS-422 and baud rate display

Release the Control buttons.

To change a value

, press and release the button that relates to the desired

value (fi gure 3-55).

ENTER PRESET VIEW

ESC

RGBHV AUDIO

CONTROL

I/O

Press and release the button(s) to configure the port as follows:

Baud rate

Enter — 9600

Preset — 19200

View — 38400

Esc — 115200

Serial protocol

RGBHV — RS-232

Audio — RS-422

The selected LEDs blink and the others remain lit.

In this example, the port is set to RS-422 at 38400 baud.

= Blinking LED

= Lit LED,

Figure 3-55 — RS-232/RS-422 and baud rate selection

Содержание MVX 128



























































































Результаты поиска

Содержание MVX 128

Отзывы:

Похожие инструкции для MVX 128

Бренды по названию

Популярные бренды

Extron electronics MVX 128, Руководство пользователя

Результаты поиска

Содержание MVX 128

Отзывы:

Похожие инструкции для MVX 128

Бренды по названию

Популярные бренды