Extron electronics MKP 3000 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 51

Extron electronics MKP 3000 Скачать руководство пользователя страница 51

MKP 3000 Remote Control Panel • Reference Information

Reference Information, cont’d

A-8

TEXT

S

ep

a

r

a

te two

piece

bu

tton here.

U

s

e notch to

remove

bu

tton.

Extron Comm-Link Control System cable

Wire specifications for Extron Comm-Link cable (figure A-3) are
as follows:

A (red) = 18 American Wire Gauge (AWG)
B (violet or blue) = 22 AWG (grouped and shielded)
C (white) = 22 AWG
D (drain) = 24 AWG
E (black) = 18 AWG

Comm-Link cable was designed for use with MKP
control panels.

SuperFlex Plenum
Jacket

Fiber Wrap

Two 22 AWG
(White and Violet or Blue)
One 24 AWG
Tinned Copper Drain Wire
(foil-shielded group)

B, C

D

Two 1

8

AWG

(Red and Black)

A, E

Figure A-3 — Extron Comm-Link cable

Changing Button Labels

The MKP ships with default labels installed in the front panel
buttons (figure 3-2, “Input/output selection mode labels), but
includes a strip of alternate labels that you can insert in one or
more of the mode selection buttons to make using the other
modes clearer.

To change the labels in the MKP’s buttons,

1

.

Remove the button from the MKP by
grasping the button firmly and
pulling it away from the panel.

Various button models are
available. Your buttons

may

appear different.

2

.

Use a small screwdriver or Extron
Tweeker to gently lever the button
cap off of the white backing plate.

3

.

Insert a button label into the cap
and gently but firmly press the
cap onto the white backing plate.

4

.

Press the button into place in the
MKP.

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

«
...
49
50
51

Содержание MKP 3000




















































Отзывы:

Нет отзывов