Extron electronics MKP 3000 Скачать руководство пользователя страница 35

Страница: 35 / 51

MKP 3000 Remote Control Panel • SIS

™

Operation

SIS

™

Operation, cont’d

MKP 3000 Remote Control Panel

Chapter Five

HTML Operation

Downloading the Startup Page

Viewing System Status

Using the Configuration Pages

Using the File Management Page

Saving and Restoring a Configuration

Special Characters

4-16

Command/r

esponse table for MKP SIS commands (continued)

Command

ASCII Command

Response

Additional description

(host to

)

to host)

IP setup, continued

Switch W

eb page priority

Esc

Cpag

Iwp

Read W

eb page priority

Esc

Cpag

Set verbose mode

Esc

Set MKP

to r

eport changes from other sources.

Read verbose mode

Esc

Read the verbose mode.

Read connection’s security level

Esc

Backup and r

estore unit configuration

Save unit configuration

Esc

{config type} XF

Cfg 1

{config type}

{config type} = 2 = unit-specific parameters

(box.config) sugh as global preset names, audio/

video input and output names. The files ar

e stor

in the dir

ectory /nortxe-backup, cr

eated on the

unit by the Save commands.

Restor

e unit configuration

Esc

0 * {config type} XF

Cfg 1

{config type}

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

Содержание MKP 3000




















































Результаты поиска

Содержание MKP 3000

Отзывы:

Extron electronics MKP 3000, Руководство пользователя, Страница: 35 / 51

Результаты поиска

Содержание MKP 3000

Отзывы: