manualshive.com logo in svg

Extron electronics FPC 6000, Руководство пользователя

Поделиться
Скачать
Extron electronics FPC 6000 Скачать руководство пользователя страница 19

F

 

XTP/LAN/PoE Input:

 (see 

figure 5

, on the previous page)

NOTE:

  The FPC 6000 can be powered by either the provided PoE power injector 

or a 12 VDC, 3 A power supply (which must be purchased separately). Do not 
remotely power the touchpanel using an XTP device. Before connecting power to the 
FPC 6000, read the Attention notifications below.

• 

XTP Input

 — Do not connect the FPC 6000 directly to an XTP source.

• 

LAN Input

 — If you use the provided 12 VDC power supply, connect the FPC 6000 

directly to the network using a twisted pair cable, terminated with an RJ-45 connector.

• 

PoE Input 

— If you use the provided PoE power injector, connect the FPC 6000 to the 

power injector output and connect the power injector input to the LAN.

• 

100-240V~50/60 Hz

1.1A MAX

INPUT

OUTPUT

POWERED TLP

LAN

To Network Device

To FPC 6000

Extron PI 140

Figure 6. 

Connecting the Power Injector

ATTENTION:

• 

Always use a power supply provided by or specified by Extron. Use of an 
unauthorized power supply voids all regulatory compliance certification and may 
cause damage to the supply and the end product.

• 

Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. 
L’utilisation d’une source d’alimentation non autorisée annule toute conformité 
réglementaire et peut endommager la source d’alimentation ainsi que le produit 
final.

• 

The installation must always be in accordance with the applicable provisions of 
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical 
Code part 1, section 16.

• 

Cette installation doit toujours être en accord avec les mesures qui s’applique 
au National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical 
Code, partie 1, section 16.

• 

These products are intended for use with a UL Listed power source marked 
“Class 2” or “LPS” and rated 12 VDC, minimum 3.0 A. or 56 VDC (PoE), 
minimum 0.8 A.

• 

Ces produits sont destiné à une utilisation avec une source d’alimentation 
listée UL avec l’appellation « Classe 2 » ou « LPS » et normée 12 Vcc, 3,0 A 
minimum ou 56 Vcc (PoE), 0,8 A minimum.

• 

The power supply shall not be permanently fixed to the building structure or 
similar structure.

• 

La source d’alimentation ne devra pas être fixée de façon permanente à une 
structure de bâtiment ou à une structure similaire.

• 

Power over Ethernet (PoE) is intended for indoor use only. It is to be connected 
only to networks or circuits that are not routed to the outside plant or building.

• 

L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur 
uniquement. Elle doit être connectée seulement à des réseaux ou des circuits qui 
ne sont pas routés au réseau ou au bâtiment extérieur.

XTP/LAN/PoE input

figure 6

mises en garde

Attention notifications

 

FPC 6000 • Panel Features

11

Содержание FPC 6000
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды