Extron electronics DTP2 R 212 Series, Руководство пользователя

Страница: 18 / 68

DTP2 R 212 Series • Installation 10
CLASS 2
WIRING
4/8 OHM
1
2
L R
Rx G Tx
HDMI HDMI
RS-232 IR
Rx Tx
OVER DTP2
Rx G Tx
RS-232
DISPLAY
POWER
12V
3.0 A MAX
RS-232
Rx Tx G
INPUTS
OUTPUT
C V G
10V 50mA
L R
VOL
REMOTE
R
DTP2 R 212 SA
LAN
OFF
SEND POWER
SIG LINK
DTP2 IN
SEND
POWER
OFF
OFF
DTP2 T 211
CONFIG
INPUT
LINK
OUTPUT
SEND
POWER
OFF
STATUS
DTP HDMI 330 Tx
CLASS 2
WIRING
4/8 OHM
1
2
L
R
Rx G Tx HDMI HDMI
RS-232 IR
Rx Tx
OVER DTP2
Rx G Tx
RS-232
DISPLAY POWER
12V
3.0 A MAX
RS-232
Rx Tx G
INPUTS OUTPUT
C V G
10V 50mA
L R
VOL
REMOTE
R
DTP2 R 212 SA
LAN OFF
SEND POWER
SIG LINK
DTP2 IN
SEND
POWER
OFF
ON
SEND
POWER
OFF
OFF
DTP2 T 211
CONFIG
INPUT
LINK
OUTPUT
SEND
POWER
OFF
STATUS
CATx Cable
up to 330' (100 m)
No Remote Power
Extron
PS 1242
(4.2 A, 50 Watts)
Local
Power Supply
Extron
DTP2 R 212 SA
Receiver
Extron
DTP HDMI 4K 330 Tx
Transmitter
DTP2 Endpoint Connected to a DTP2 Endpoint
CATx Cable
up to 330' (100 m)
Direction of
Remote Power
Extron
DTP2 R 212 SA
Receiver
Extron
DTP2 T 211
Transmitter
Extron
PS 1242
(4.2 A, 50 Watts)
Figure 5. DTP2 R 212 SA Send Power Toggle Switch Configuration
F
HDMI output (see figure 3 on page 7) — Connect an HDMI display device to this
female Type A HDMI port. The EDID information is read from the connected output
device via this port and is written to memory on each input whenever the output device
is connected to this port and powered on.
NOTE:
The EDID information is also read and stored whenever power is recycled to
the connected output device or when the output device is replaced.
G
Audio output — Connect a 5‑pole captive screw connector for balanced or
unbalanced analog audio output. This audio output is not amplified and can be
connected to an external amplifier.
H
Amplified audio output (SA models only) — Connect a 4‑pole captive screw
connector for amplified audio output to external speakers.
I
Display control — Use 3‑pole captive screw connector for bi‑directional RS‑232
control of a connected display device.
J
Remote amplified volume control port (SA models only) — Connect an external
audio controller to control volume and mute levels remotely via this 3.5 mm, 3‑pole
captive screw port (see
Remote Control (SA models only) on page 15 for more
information and to wire the connection).
K
Switch for volume control (SA models only) — When using the amplified output
connector (
H
), flip the switch to the lower position for remote volume control of the
amplified output through port
J
.
L
Remote RS-232 port — Connect a serial RS‑232 device via this 3.5 mm, 3‑pole
captive screw port for remote control of the DTP2 R 212 (see Display and Remote
RS-232 Control on page 15 to wire the connector).
M
LAN (Ethernet) port — Use an RJ‑45 cable to connect this jack to a LAN (Ethernet)
for control of the device.
5