Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 80

Страница: 80 / 135

3. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 57

Attaching the rear brackets to the device

Screws, 8-32 x 5/16-in., panhead Phillips

Mid-mounting

Observe the following notes when using this procedure:

•

The device must be turned off and disconnected from the fabric during this procedure.

•

The illustrations in this document show a 1U device, but the instructions are the same for a 2U device.

•

The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a rack:

Attaching the front brackets to the device

on page 80

Attaching the front brackets to the rack

on page 81

Attaching the rear brackets to the rack

on page 82

Attaching the rear brackets to the device

on page 83

Attaching the front brackets to the device

Complete the following steps to attach the front brackets to the device.

1. Position the right front bracket with the flat side against the right side of the device, as shown in

Figure 58

Installing the Universal Two-Post Rack Kit (XBR-R000294)

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды