Extreme Flight YAK-54 ARF Скачать руководство пользователя | Manualshive

Страница: 15 / 50

background image

Wing Assembly

16.

The assembly process for the wing is almost identical to that of the
stab/elevator. For this reason we will not go into quite as much detail
as in the previous procedure. Remove the aileron from the wing
panel. Locate the 2 slots for the control horns and remove the
covering from the slots with a sharp #11 blade.

Follow the same

procedure as outlined previously to install the control horns into
the control surface and hinge the wing.

You may need to trim

1/16” from the front of the composite base plate to prevent
overhanging the bevel. Repeat this procedure for the other wing.

15

«
...
13
14
15
16
17
...
»

Содержание YAK-54 ARF



















































Отзывы:

Нет отзывов

Похожие инструкции для YAK-54 ARF

Бренд: Jamara Страницы: 12

P-47 Thunderbolt

Бренд: Jamara Страницы: 12

FORNEY LIVE STEAM

Бренд: Accucraft trains Страницы: 12

F/A-18E interior S.A.

Бренд: Eduard Страницы: 4

ACCUCRAFT 7/8 SCALE 7 x 12 INCH BAGNALL

Бренд: Accucraft Страницы: 8

Бренд: Viessmann Страницы: 2

Smart Bluetooth Robot Car

Бренд: Uctronics Страницы: 42

Toot-Toot Drivers CustomisablePeople Carrier

Бренд: VTech Страницы: 11

Micro Citabria RTF

Бренд: PARKZONE Страницы: 11

Бренд: Bigben Страницы: 52

Бренд: Maison Battat Страницы: 2

Kawasaki Adventure 4x4

Бренд: Power Wheels Страницы: 28

Бренд: Desktop Locomotive Works Страницы: 2

Бренд: Ripmax Страницы: 12

Бренд: Blade Страницы: 16

Бренд: marklin Страницы: 2

Бренд: Tek Nek Toys International Страницы: 2

Бренд: PLAYTIVE JUNIOR Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды