Extreme Flight Extra 330 LT Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 31

background image

The 12oz. Forutitude fuel tank is great upgrade.

The 75" Extra includes vent covers for

the pipe tunnel. We suggest using these

to provide maximum cooling. Note: the

covering over the vents must be cut out.

Due to additional vibration of the gas engine, we recommend using the included canopy

screws and blind nuts. The blind nuts must be installed on the tabs as shown.

27

«
...
25
26
27
28
29
...
»

Содержание Extra 330 LT
































Отзывы:

Нет отзывов

Похожие инструкции для Extra 330 LT

Бренд: Old School Model Works Страницы: 14

Бренд: LAEGENDARY Страницы: 32

Бренд: Makita Страницы: 80

Бренд: J-Power Group Страницы: 19

Бренд: GRAUPNER Страницы: 42

Бренд: BLOTZ Страницы: 3

Бренд: marklin Страницы: 20

Бренд: Gyros Страницы: 7

Model Space D51 200

Бренд: De Agostini Страницы: 10

Бренд: GAME OF BRICKS Страницы: 32

Verkehrsschranke Grand

Бренд: Jamara Страницы: 4

Albatross D III

Бренд: REVELL Страницы: 6

No. 9 pay as you enter

Бренд: M.T.H. Страницы: 23

Megaphone Mission Voice Changer

Бренд: VTech Страницы: 12

Бренд: Tabletop Scenics Страницы: 12

Spitfire F.Mk.22/24 landing flaps

Бренд: Eduard Страницы: 2

Бренд: Extreme RC Страницы: 4

Бренд: Flex innovations Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды