manualshive.com logo in svg

Extreme Flight RC EXTRA 300 EXP V2, Инструкция по сборке

Поделиться
Скачать
Extreme Flight RC EXTRA 300 EXP V2 Скачать руководство пользователя страница 11

www.modellmarkt24.ch;    www.modellmarkt24.de

11 

 

 

7. Locate the aileron servo mount and remove the covering from this area. Use a sealing 
iron to seal the edges of the covering to the sides of the servo opening. Take a few minutes 
to apply some CA to the joints of the servo rails and the ribs. 

 

8

. 

Attach a 12” servo extension to your servo and secure with thread

 or heat shrink 

tubing. Use the manufacturer supplied mounting hardware and install the servo with the 
output shaft toward the trailing edge of the wing. Electronically center your servo.  

Aileron servo arm length should be 1.50”. We recommend the 

Extreme Flight anodized 

servo arms.  Thread 2 ball links onto the titanium turnbuckle pushrod.  Secure the 
pushrod to the control horns and servo arm as shown in the picture using the supplied 
3mm bolts and nylon insert locknuts. Make sure to place the conical spacer between the 
ball link and aluminum servo arm to prevent binding.  As always, use blue Loctite on ALL 
bolts! 

www.modellmarkt24.ch;    www.modellmarkt24.de

Содержание EXTRA 300 EXP V2































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды