- 39 -
- 38 -
EN
the battery is fully charged. The
manufacturer reserves the right to
change the indication of the charging
process / charged state with respect
to the possible changes in the manu-
facturing process.
y
Charge the compressor at an ambient
temperature and device temperature
in the range from +10°C and 40°C.
Charging at a temperature that
is too low impedes the charging
process and at a higher than specified
temperature there is risk of damage
caused by high temperature because
heat is generated during the charging
process.
USING THE INFLATION
ADAPTERS
y
Screw the inflation adapter into the
hose inflation flange.
Adapter (fig. 2, position 1) is inten-
ded for oral inflation valves. The
inflation tube (fig. 2, position 2) that
is inserted into the valve on the ball
is intended for inflating balls.
For inflating tyre tubes, connect the
hose to the valve by means of a tyre
tube adapter (fig. 2, position 3).
INFLATING
WITH A COMPRESSOR
Step 1
y
Screw the air hose into the compressor.
Step 2
y
Screw the flange of the inflation
hose on to the tyre valve.
Step 3
y
Set the toggle switch upwards (the
ON symbol will be visible on the
toggle switch) (Step 3).
The compressor will turn on and the
display will show the current pressu-
re in the tyre. If the compressor is not
connected to a tyre that is pressuri-
sed, after 1 minute of inactivity, and
the compressor will also turn off and
when the toggle switch is set to the
„ON“ position to protect the battery
against discharging (it will enter the
sleep mode). If the compressor is in
sleep mode, press the „M“ button,
which will switch the compressor
from sleep mode to active mode.
Step 4
y
Set the pressure units by pressing
and holding down the „M“ button
(fig. 1, position 6). To change the
pressure units, it is always necessary
to press and hold down the „M“
button. If the button is only pressed
for a short time, the inflation process
will be started.
Step 5
y
Repeatedly pressing button (fig. 1,
position 4) can be used to set the
symbol of a car, motorcycle, bicycle
or ball with a preset default pressure
value for the given vehicle/item
shown on the display so that it is not
necessary to set the value entirely
from zero, or this button can be used
to set the default value to 0. The
preset pressure values for the given
vehicle/item are only approximate
and must be adjusted according to
the vehicle manufacturer‘s instruc-
tions to the required tyre pressure.
Subsequently, use buttons „+“ or „-“
to adjust/set the required pressure
value.
III. Parts and
control elements
Fig. 1, position-description
1) Hose flange for screwing
on to the valve or inflation adapters.
2) On/Off toggle switch
3) Display
4) Car-motorcycle-bicycle-ball selec-
tion button (this delivers a preset
pressure value for a car-motorcycle-
-bicycle-ball)
5) „–“ button for reducing
the pressure value
6) „M“ button for activating the sleep
mode; setting pressure units;
turning inflation on/off
7) „+“ button for increasing
the pressure value
8) Turn on LED lamp button
9) Inflation hose
10) LED lamp
11) USB-C charging connector
12) Charging process and full charge
LED indicator
Fig. 2, position-description
1) Universal adapter for insertion
into (oral) inflation valves.
2) Tube for inflating balls
3) Tyre valve adapter
IV. Using
the compressor
•
ATTENTION
y
Carefully read the entire user‘s
manual before first use and keep it
with the product so that the user can
learn about it. If you lend or sell the
product to somebody, include this
user‘s manual with it. Prevent this
user‘s manual from being damaged.
CHARGING THE COMPRESSOR
•
ATTENTION
y
For inflating with air, it is necessary
for the compressor to be sufficiently
charged.
y
Charge the compressor using
a computer USB port or a charger
with a USB port, etc. The compressor
has integrated electronic protection
against input charging current
greater than 1 A, meaning that the
compressor can charge from a USB
port regardless of how high the
charging current is, because the
compressor will be charged with
a current no greater than 1 A. Using
a USB charging power source with
a current greater than 1 A will not
speed up the charging process. When
the battery is fully charged in the
compressor, the charging process is
automatically stopped and overchar-
ging of the battery cannot occur even
when the compressor is connected to
the charger after it is fully charged.
y
The charging process and full charge
state are indicated by an LED indicator
on the compressor (fig. 1, position 12).
y
The indicator light is lit red during
the charging process, and blue when