Extech Instruments VB500 Скачать руководство пользователя страница 14

Страница: 14 / 14

VB500-EU-EN-V1.2-10/11

Battery Replacement and Disposal

When the low battery icon

appears on the LCD, the batteries must be replaced. Several hours of

accurate readings are still possible in this condition; however batteries should be replaced as soon
as possible:

•

Remove the two (2) Phillips screws from the rear of the meter at the 12 and 6 o’clock positions.

•

Remove and safely place the battery compartment and screws where they will not be damaged
or lost.

•

Replace the eight (8) 1.5V ‘AA’ batteries observing polarity.

•

Replace the battery compartment cover with the two (2) Phillips screws.

All EU users are legally bound by the battery ordinance to return all used batteries to
collection points in your community or wherever batteries / accumulators are sold!
Disposal in the household garbage is prohibited!

Copyright © 2011 Extech Instruments Corporation (a FLIR company)

www.extech.com

Содержание VB500















Результаты поиска

Содержание VB500

Отзывы:

Похожие инструкции для VB500

Бренды по названию

Популярные бренды

Extech Instruments VB500, Руководство пользователя

Результаты поиска

Содержание VB500

Отзывы:

Похожие инструкции для VB500

Бренды по названию

Популярные бренды