Extech Instruments 382095 Скачать руководство пользователя страница 4

Страница: 4 / 42

382095 V4.1 7/06

Support line (781) 890-7440

Technical support: Extension 200; E-mail: [email protected]

Repair & Returns: Extension 210; E-mail: [email protected]

Product specifications subject to change without notice

For the latest version of this User’s Guide, Software updates, and other

up-to-the-minute product information, visit our website: www.extech.com

Extech Instruments Corporation, 285 Bear Hill Rd., Waltham, MA 02451

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and

workmanship for one year from date of shipment (a six month limited warranty applies to sensors and

cables). If it should become necessary to return the instrument for service during or beyond the warranty

period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our

website www.extech.com for contact information. A Return Authorization (RA) number must be issued

before any product is returned to Extech. The sender is responsible for shipping charges, freight, insurance

and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from

action of the user such as misuse, improper wiring, operation outside of specification, improper

maintenance or repair, or unauthorized modification. Extech specifically disclaims any implied warranties or

merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or

consequential damages. Extech's total liability is limited to repair or replacement of the product. The

warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied.

Calibration and Repair Services

Extech offers repair and calibration services

for the products we sell. Extech also provides NIST

certification for most products. Call the Customer Service Department for information on calibration
services available for this product. Extech recommends that annual calibrations be performed to verify
meter performance and accuracy.

Copyright

2006 Extech Instruments Corporation

Содержание 382095











































Результаты поиска

Содержание 382095

Отзывы:

Похожие инструкции для 382095

Бренды по названию

Популярные бренды

Extech Instruments 382095, Руководство пользователя

Результаты поиска

Содержание 382095

Отзывы:

Похожие инструкции для 382095

Бренды по названию

Популярные бренды