Exlar Curtiss-Wright Tritex II Series Скачать руководство пользователя страница 45

Страница: 45 / 78

Curtiss-Wright | TRITEX II AC 75 Rev. K PN61928 7/12/2022

Logic and IO Power Supply

The 75 mm Tritex contains a built in 24 Volt power supply, this supply

can be used to power the optional internal brake as well as provide some

power for the IO. The maximum current the internal 24 V can provide is

600 mA. The brake will use 500 mA that only leaves 100 mA available

for other IO if a brake is provided.

Optionally an external 24 VDC power supply may be connected to the

IO+V and IO Com connections, see diagram below. When an external

24 Volt supply is connected it effectively bypasses the internal 24 Volt

supply and provides power for logic backup, IO and the brake. If the

external 24 Volt supply remains powered when the main Tritex AC power

is removed it will maintain position information (position feedback is still

powered and active) so re-homing is not required and keeps

communications active to networked system components. A fuse is

necessary unless power supply self-limits at 3A or less.

Control Logic Power Supply Wiring and Fusing

Volts

Amps

Fuse

Wire

24V dc +/- 10%.

2 Amp, if power supply is

not limited at 3A or less

18 AWG (0.8 mm^2)

Wiring for External 24 Volt Supply

CAUTION

It is important that the 24 VDC power supply or logic and I/O

is connected to the circuit common and also shall be

externally grounded to PE.

Содержание Curtiss-Wright Tritex II Series















































































Результаты поиска

Содержание Curtiss-Wright Tritex II Series

Отзывы:

Бренды по названию

Популярные бренды

Exlar Curtiss-Wright Tritex II Series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Curtiss-Wright Tritex II Series

Отзывы:

Бренды по названию

Популярные бренды