EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 638 / 803

Test Functions

626

88000 Series

S-OAM Link Trace

S-OAM Link Trace

From the

Test

menu, tap

Functions

, and the

S-OAM Link Trace

tab.

Link Trace



Priority

allows selecting the VLAN user priority:

(default) to

. Refer

VLAN ID and Priority

on page 758 for more information.



Drop Eligible

is set to

(no frames will be dropped when

congestion occurs) and is not configurable.



TTL

sets the Time To Live value:

255

(default is

128



Link Trace

button when ON (OFF by default) starts the link trace

process. The

Link Trace

button turn OFF automatically once the link

trace process is completed.

Result

The table reports the following information for each valid LTR frames
received in response to the last LTM frame sent:

TTL

MEP/MIP MAC

Address

Forward

, and

Term MEP



Last Link Trace Status

displays the last link trace status.



TX LTM

indicates the count of transmitted LTM frames.

1. Available when VLAN is enabled (see

VLAN

on page 225).

Status

Description

Pending

No Results

Successful

Last Link Trace was successful

Failed – LTR Timeout

Last Link Trace failed due to a LTR Timeout

Failed – Invalid LTR

Last Link Trace failed due to an Invalid LTR

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды