EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 327 / 803

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

315

Streams - Profile

Streams - Profile

The Traffic Gen & Mon test application supports the configuration of up to
16 different streams individually.

From the

Test

menu, tap

Setup

,

Test Configurator

, the protocol block, and

the

Profile

tab.

Note:

All parameters are configurable per stream.

Stream Selection and Activation

Select the stream to be configured by either using the left/right arrow or by
tapping over the stream numbers area then tapping on a specific stream
number. An orange background indicates the selected stream while a
green background indicates the streams that are enabled.



Stream

associates a name to the selected stream number. Default

stream names are

Stream 1

to

Stream n

.



Enable

check box when selected (cleared by default) enables the

selected stream. However, the stream will be generated only when the
test is started while the global

Enable TX

check box is selected from

the

Global

tab.

«
...
325
326
327
328
329
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: eclisse Страницы: 40

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Vag Страницы: 15

Бренд: Kampmann Страницы: 5

Бренд: Zander Aachen Страницы: 75

Бренд: Grundfos Страницы: 23

Series RHCN-7000

Бренд: Omega Engineering Страницы: 2

xComfort CHSZ-12/03

Бренд: Eaton Страницы: 4

Бренд: WAM Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Madas Страницы: 10

Interface Module XC

Бренд: Baer Страницы: 12

Бренд: RADIKAL TECHNOLOGIES Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды