EXFO CT440 Series Скачать руководство пользователя страница 24

Страница: 24 / 169

Getting Started with Your CT440

CT440

Installing the CT440 in a Rack

Installing the CT440 in a Rack

To be able to install the CT440 in a rack, you must first install the rack-mounting brackets on
each side of the instrument.

The brackets are delivered with eight screws (8 mm) to fasten it on each side panels of the
instrument with a Phillips head screwdriver.

To install the rack-mounting brackets on the CT440:
1.

Loosen the four screws (6 mm) on each side of the CT440 case, as illustrated in the
following figure.

Position the left-side bracket on the side panel so that you see the screw holes on the

side panel, and it is flush with the front panel of the instrument.

Attach the bracket to the side panel with the four 8 mm screws provided with the

bracket, using a phillips head screwdriver.

Perform steps 2 and 3 with the right-side bracket.

Содержание CT440 Series










































































































































































Результаты поиска

Содержание CT440 Series

Отзывы:

Похожие инструкции для CT440 Series

Бренды по названию

Популярные бренды

EXFO CT440 Series, Руководство пользователя

Результаты поиска

Содержание CT440 Series

Отзывы:

Похожие инструкции для CT440 Series

Бренды по названию

Популярные бренды