background image

Using The Valet Button

Security System Features (cont’d)

SECURECODE

  SecureCode allows you to customize the number of valet presses required to perform 

an emergency override This is an extra layer of security that prevents anyone from 

overriding the alarm even if they have a key to the vehicle SecureCode has 2 stages 

with the first requiring 1-9 button valet presses and the second requiring 0-9 valet button 

presses This gives you 99 possible combinations To program a custom SecureCode, 

please refer to user feature #13 on Page 18 

To perform an emergency override with SecureCode, use the following steps:

STEP 1 - 

With the system armed, enter the vehicle (the alarm will activate)

STEP 2 - 

Turn the ignition switch to the “ON” position

STEP 3 - 

Within 5 seconds of step 2, press the valet switch to enter the first digit of your 

programmed code

STEP 4 - 

After a few seconds, the siren will stop sounding and chirp once (confirming 

stage 1) The siren will then continue sounding

STEP 5 - 

Now, within 5 seconds of step 4, press the valet switch to enter the second digit 

of your code If the code is correct, the alarm will disarm

EMERGENCY OVERRIDE

  If you were to lose or break your controller, you’d need to perform an emergency 

override to disarm the system and use your vehicle To do so, use the following steps:

STEP 1 - 

Enter the vehicle (the alarm should sound)

STEP 2 - 

Turn the ignition key to the “ON” position

STEP 3 - 

Press the valet switch (located in the window-mount antenna) once 

   NOTE: Enter your SecureCode at this time if programmed via user feature #13

STEP 4 - 

Turn the ignition key “OFF”

If the code is entered incorrectly, you must turn the ignition key OFF, then back 

ON to try again

 

Additionally, if 2 failed attempts are made, the alarm will ignore 

any further attempts for 2 minutes

WHEN THE SYSTEM TRIGGERS

  It will sound the siren/horn and flash the parking lights for 30 seconds (programmable). 

At this point you will also be notified on the controller as to which zone is violated (while 

in range) When disarming after a trigger event, the siren/horn will chirp 4 times and the 

parking lights will flash 4 times instead of the standard 2 times.  

ZONE INDICATORS (1 FLASH = CAR1, 2 FLASHES = CAR2):

HOOD: LOCK + UNLOCK LEDs will flash

DOOR: LOCK + START LEDs will flash

SENSOR: All 4 LEDs will flash

LOCK ON TRIGGER:

 If a door is opened when the system is triggered, it will wait until the 

door is closed again, then lock the doors This feature combats “slim jim” type devices

STORM SAFE MODE:

 When the system is triggered, pressing the UNLOCK button will 

stop the alarm from sounding but will leave the doors locked 

NUISANCE PREVENTION:

 If the system pre-warns 5 times within 15 minutes, it will 

bypass the zone for the remainder of the 15 minutes before rearming the pre-warn zone 

Additionally, if a full trigger zone is left open, the system will trigger a total of 3 times 

before bypassing the zone Once the zone is closed again, it will re-arm that zone

10

Содержание AL-1775-3DB


























Отзывы: