manualshive.com logo in svg

Exar XRT86VX38, Руководство пользователя

Поделиться
Скачать
Exar XRT86VX38 Скачать руководство пользователя страница 51

 

XRT86VX38

47

REV. 1.0.3

8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION

4

TxFr1544

R/W

0

Fractional/Signaling Interface Enabled

This bit is used to enable or disable the transmit fractional data interface, sig-
naling input, as well as the 32MHz transmit clock and the transmit overhead 
Signal output. 

0 = Configures the 5 time slot identifier pins (TxChn[4:0]) to output the channel 
number as usual.

1 = Configures the 5 time slot identifier pins (TxChn[4:0]) to function as the fol-
lowing:

TxChn[0] becomes the Transmit Serial SIgnaling pin (TxSIG_n) for signaling 
inputs. Signaling data can now be input from the TxSIG pin if configured 
appropriately.

TxChn[1] becomes the Transmit Fractional Data Input pin (TxFrTD_n) for frac-
tional data input. Fractional data can now be input from the TxFrTD pin if con-
figured appropriately.

TxChn[2] becomes the 32 MHz transmit clock output

TxChn[3] becomes the Transmit Overhead Signal which pulses high on the 
first bit of each multi-frame.

N

OTE

:  This bit has no effect in the high speed or multiplexed modes of 

operation. In high-speed or multiplexed modes, TxCHN[0] functions 
as TxSIGn for signaling input.

3

TxICLKINV

R/W

0

Transmit Clock Inversion (Backplane Interface)

This bit selects whether data transition will happen on the rising or falling edge 
of the transmit clock.

0 = Selects data transition to happen on the rising edge of the transmit clocks.

1 = Selects data transition to happen on the falling edge of the transmit clocks.

N

OTE

:  This feature is only available for base rate configuration (i.e. non-

highspeed, and non-multiplexed modes).

2

TxMUXEN

R/W

0

Multiplexed Mode Enable

This bit enables or disables the multiplexed mode. When multiplexed mode is 
enable, multiplexed data of four channels at 12.352 or 16.384MHz are demul-
tiplexed inside the transmit framer and sent to 2 channels on the line side. The 
backplane speed will be running at either 12.352 or 16.384MHz depending on 
the multiplexed mode selected by TxIMODE[1:0] of this register.   

0 = Disables the multiplexed mode. 

1 = Enables the multiplexed mode. 

T

ABLE

 30: T

RANSMIT

 I

NTERFACE

 C

ONTROL

 R

EGISTER

 (TICR)                                              H

EX

 A

DDRESS

:0

X

N120

B

IT

F

UNCTION

T

YPE

D

EFAULT

D

ESCRIPTION

-O

PERATION

Содержание XRT86VX38












































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды