manualshive.com logo in svg

Exar XRT86VX38, Руководство пользователя

Поделиться
Скачать
Exar XRT86VX38 Скачать руководство пользователя страница 26

XRT86VX38

 

22

8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION

REV. 1.0.3

3-2

Transmit AIS 
Pattern 
Select[1:0]

R/W

00

Transmit AIS Pattern Select[1:0]:

These two bits permit the user to do the following.

1. To select the appropriate AIS Pattern that the Transmit T1 Framer block will 
transmit to the remote terminal equipment, and

2. To command (via Software Control) the Transmit T1 Framer block to transmit 
that particular AIS Pattern to the remote terminal equipment, as depicted below.

N

OTE

:  For normal operation (e.g., to configure the Transmit T1 Framer block to 

transmit normal T1 traffic) the user should set this bit to “[X, 0]”

1-0

AIS Defect 
Declaration 
Criteria [1:0]

R/W

00

AIS Defect Declaration Criteria[1:0]:

These bits permit the user to specify the types of AIS Patterns that the Receive T1 
Framer block must detect before it will declare the AIS defect condition.

T

ABLE

 7: A

LARM

 G

ENERATION

 R

EGISTER

 (AGR)                                                            H

EX

 A

DDRESS

: 0

X

N108

B

IT

F

UNCTION

T

YPE

D

EFAULT

D

ESCRIPTION

-O

PERATION

AISG[1:0]

T

YPES

 

OF

 AIS P

ATTERNS

 T

RANSMITTED

00/10

Disable AIS Alarm Generation

The Transmit T1 Framer block will transmit “normal” T1 
traffic to the remote terminal equipment.

01

Enable Unframed AIS Alarm Generation

 

Transmit T1 Framer block will transmit an Unframed All 
Ones Pattern, as an AIS Pattern.

11

Enable Framed AIS Alarm Generation

Transmit T1 Framer block will transmit a Framed, All 
Ones Pattern, as the AIS Pattern.

AISD[1:0]

AIS Defect Declaration Criteria

00/10

AIS Detection Disabled

AIS Defect Condition will NOT be declared.

01

Enable Unframed and Framed AIS Alarm Detection

ReceiveT1 Framer block will detect both Unframed and 
Framed AIS pattern

11

Enable Framed AIS Alarm Detection

Receive T1 Framer block will detect only Framed AIS pat-
tern

Содержание XRT86VX38












































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды