manualshive.com logo in svg

Exar XRT86VX38, Руководство пользователя

Поделиться
Скачать
Exar XRT86VX38 Скачать руководство пользователя страница 17

 

XRT86VX38

13

REV. 1.0.3

8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION

T

ABLE

 3: L

INE

 I

NTERFACE

 C

ONTROL

 R

EGISTER

 (LICR)                                                            H

EX

 A

DDRESS

: 0

X

N101

B

IT

F

UNCTION

T

YPE

D

EFAULT

D

ESCRIPTION

-O

PERATION

7

FORCE_LOS

R/W

0

Force Transmit LOS (To the Line Side)

This bit permits the user to configure the transmit direction circuitry 
(within the channel) to transmit the LOS pattern to the remote terminal 
equipment, as described below.

0 - Configures the transmit direction circuitry to transmit “normal” traffic.

1 - Configures the transmit direction circuitry to transmit the LOS 

Pattern.

6

Reserved

R/W

0

Single Rail Mode

This bit can only be set if the LIU Block is also set to single rail mode.  
See Register 0xNFE0, bit 7.

0 - Dual Rail

1 - Single Rail

5:4

LB[1:0]

R/W

00

Framer Loopback Selection 

These bits are used to select any of the following loop-back modes for 
the framer section. For LIU loopback modes, see the LIU configuration 
registers. 

3:2

Reserved

R/W

0

Reserved

LB[1:0]

T

YPES

 O

F

 L

OOP

B

ACK

 S

ELECTED

00

Normal Mode (No LoopBack)

01

Framer Local LoopBack: 

When framer local loopback is enabled, the transmit 
PCM input data is looped back to the receive PCM out-
put data. The receive input data at RTIP/RRING is 
ignored while an All Ones Signal is transmitted out to 
the line interface.

10

Framer Far-End (Remote) Line LoopBack:

When framer remote loopback is enabled, the digital 
data enters the framer interface, however does not 
enter the framing blocks. The receive digital data from 
the LIU is allowed to pass through the LIU Decoder/
Encoder circuitry before returning to the line interface.

11

Framer Payload LoopBack: 

When framer payload loopback is enabled, the raw 
data within the receive time slots are looped back to the 
transmit framer block where the data is re-framed 
according to the transmit timing.

Содержание XRT86VX38












































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды