background image

Exalto Wiper Technologies 

type CT3N

6

If using 

one

 speed motors:

Speed bar

Waiting time

Mode

All Leds OFF

-

Stand-by

1 x Led ON

8 seconds

Intermittent

2 x Led ON

6 seconds

Intermittent

3 x Led ON

4 seconds

Intermittent

4 x Led ON

2 seconds

Intermittent

5 x Led ON

-

Continuous

4.  Wash program

By pressing the wash button, washing program will start.

  

|3 sec. 

3 sec.  | 

4 sec.     |

   

|=== Spray === Spray ===|

   

 

 

|===== Wipe ===== Wipe ===|

Keep pressed button 5 to increase wash timing and spray + wipe time. After wash 
cycle, wipers will return to operate in the previous selected mode.

5.  Single wipe function

The single wipe function is allowed only when all the wipers are off. Push the button 
6 to perform the single wipe. Keep pushed to perform more than one wipe.

6.   Heating function (additional relay box required)

The control panel can activate/deactivate the heaters, only if a relay box (additional) 
is installed. The button 4 actives the heaters when pushed. To deactivate push the 
button again. When the heaters are active, the button is lighted up.

 

7.  Backlight brightness and colors

The button 3 performs the brightness adjustment and the color selection. Pushing 
it momentary the brightness level will change. Four brightness levels are available. 
Keeping it pushed the backlighting color will change.

Содержание 210321224-210351224













Отзывы: