Exalt EX i GigE Series Скачать руководство пользователя страница 68

Страница: 68 / 133

Exalt Installation and Management Guide

EX-i Series FDD Digital Microwave Radios

202675-005

2011-08-30

The “new value” list matches the “current value” list to allow easy editing by subtracting, adding, or

otherwise modifying the list before clicking Update.

VLAN configurations are maintained even when VLAN is disabled. That is, the VLANs can be

configured and the configuration saved, even though they are not active until VLAN is enabled. Use

the following methods to restore the management connection if a mistake was made assigning the

management VLAN and access cannot be restored:

•

Reset the radio to the critical factory defaults (see

Reset to Critical Factory Settings

), or

•

Connect to the Console port using a serial interface and the CLI, as described in

Command Line

Interface (CLI)

, and reconfigure the VLAN settings.

Note:

The VLAN IDs that are assigned to any interface should support the Function settings

on each interface as defined on the

Ethernet Interface Configuration Page

Содержание EX i GigE Series






































































































































Результаты поиска

Содержание EX i GigE Series

Отзывы:

Похожие инструкции для EX i GigE Series

Бренды по названию

Популярные бренды

Exalt EX i GigE Series, Руководство по установке и управлению

Результаты поиска

Содержание EX i GigE Series

Отзывы:

Похожие инструкции для EX i GigE Series

Бренды по названию

Популярные бренды