EWM Taurus 401 Basic FKW Скачать руководство пользователя страница 55

Страница: 55 / 70

Design and function

Machine configuration menu

099-005230-EW501

02.04.2014

5.12

Machine configuration menu

5.12.1

Selecting, changing and saving parameters

NOTE

ENTER (Enter the menu)

• Switch off the machine at the main switch.
• Press and hold the "welding procedure" push-button and switch the machine on again at

the same time.

NAVIGATION (Navigate the menu)

• Select parameters by turning the "welding parameter setting" rotary knob.
• Set or change the parameters by turning the "welding voltage" rotary knob.

EXIT (Exit the menu)

• Press the "gas test" push-button (switch machine off and on again).

ENTER

EXIT

NAVIGATION

Figure 5-22

Display

Setting/selection

Lead resistance 1

Lead resistance for the first welding circuit 0

mΩ–60 mΩ (8 mΩ ex works).

Only qualified service personnel may change the parameters!

Time-based power-saving mode

• 5 min.–60 min. = Time to activation of power-saving mode in case of inactivity.
• off = inactivated

5.12.2

Power-saving mode

The power-saving function can be activated either by pressing the button for a longer time (see chapter
"Machine description

– Short overview") or by setting a parameter in the configuration menu (time-based

power-saving mode).

When power-saving mode is activated, both machine displays show the horizontal digit in the
centre of the display only.

Pressing any operating element (e.g. tapping the torch trigger) deactivates power-saving mode and the
machine is ready for welding again.

Содержание Taurus 401 Basic FKW







































































Результаты поиска

Содержание Taurus 401 Basic FKW

Отзывы:

Похожие инструкции для Taurus 401 Basic FKW

Бренды по названию

Популярные бренды

EWM Taurus 401 Basic FKW, Руководство по эксплуатации

Результаты поиска

Содержание Taurus 401 Basic FKW

Отзывы:

Похожие инструкции для Taurus 401 Basic FKW

Бренды по названию

Популярные бренды