EWM Taurus 401 Basic FKW Скачать руководство пользователя страница 46

Страница: 46 / 70

Design and function

MIG/MAG welding

099-005230-EW501

02.04.2014

Latched mode

Figure 5-14

Step 1

•  Press and hold torch trigger
•  Shielding gas is expelled (gas pre-flows)
•  Wire feed motor runs at “creep speed”.
•  Arc ignites after

the wire electrode makes contact with the workpiece; welding current flows.

• Change over to pre-selected WF speed (main program P

Step 2

• Release torch trigger (no effect)

Step 3

• Press torch trigger (no effect)

Step 4

•  Release torch trigger
•  WF motor stops.
•  Arc is extinguished after the preselected wire burn-back time expires.
•  Gas post-flow time elapses.

5.8.6

Standard MIG/MAG torch

The MIG welding torch trigger is essentially used to start and stop the welding process.

Operating elements

Functions

Torch trigger

• Start/stop welding

5.8.7

MIG/MAG special-torches

Function specifications and more indepth information can be found in the operating manual for
the relevant welding torch!

Содержание Taurus 401 Basic FKW







































































Результаты поиска

Содержание Taurus 401 Basic FKW

Отзывы:

Похожие инструкции для Taurus 401 Basic FKW

Бренды по названию

Популярные бренды

EWM Taurus 401 Basic FKW, Руководство по эксплуатации

Результаты поиска

Содержание Taurus 401 Basic FKW

Отзывы:

Похожие инструкции для Taurus 401 Basic FKW

Бренды по названию

Популярные бренды