EWM Picotig 180 Скачать руководство пользователя страница 21

Страница: 21 / 57

Functional characteristics

TIG welding

Item No.: 099-002046-EWM01

Functional characteristics

5.1

TIG welding

5.1.1

Selection and adjustment

Operating
element

Action Result

Select welding process

MMA welding

TIG welding (non-latched operating mode)

TIG welding (latched operating mode)

Green signal light: HF ignition (non-contact) switched on
Red signal light: Liftarc ignition (contact ignition) switched on

AMP

sec

Set welding current

Select secondary current

AMP%

AMP

sec

Set secondary current
Setting range 1% to 200% (percentage of main current)

Select down-slope time

AMP

sec

Set down-slope time

Setting range 0.0 s to 20.0 s

Select gas post-flow time

sec

AMP

sec

Set gas post-flow time
Setting range 0.0 s to 20.0 s

NOTE

This completes the basic settings and you can now start welding.

Other parameters, such as gas pre-flow time, are already set for the most common applications.
To change these parameters, see the "Advanced settings" chapter.

5.1.2

TIG automatic cut-out

NOTE

The automatic cut-out function will be triggered by two conditions during the welding

process:

During the ignition phase (ignition fault)
• If there is no welding current within 3s after starting the welding.

During the welding phase (arc interruption)
• If the arc is interrupted for longer than 3s.

In both cases, the welding machine ends the ignition or welding process immediately.

Содержание Picotig 180


























































Результаты поиска

Содержание Picotig 180

Отзывы:

Похожие инструкции для Picotig 180

Бренды по названию

Популярные бренды

EWM Picotig 180, Руководство по эксплуатации

Результаты поиска

Содержание Picotig 180

Отзывы:

Похожие инструкции для Picotig 180

Бренды по названию

Популярные бренды