background image

The UZC4 Universal Zone Control System allows you to easily 
upgrade an inefficient single zone HVAC system, into an 
Automated, Multi-zone, Energy saving, Comfort producing, 
Safety Minded, HVAC system. With Superior design, Intuitive 
firmware, Building Code Compliant support, Simple setup 
options, and Easy to understand wiring, the UZC4  Zoning 
system is the Designer/Contractors dream. Combined with 
Patented EWC motorized dampers and practically any Off-the-
shelf Conventional or Heat Pump style Thermostats,        

EWC has set a New Industry Standard in Large 
Residential and Commercial HVAC Air Zoning Systems.

The main module controls four air zones 
using 24 vac motorized air dampers and 
may be expanded up to 

22

 zones, using 

ZXM2 Expansion Modules. 

See page 23.

The UZC4 will Control 2, 3 & 4 stage 
Conventional, GeoThermal or Dual Fuel 
Heat pumps, 

without the need for dual 

fuel kits. 

 Also single or multi-stage Gas, 

Oil, & Hydronic HVAC systems, with 
single or two stage cooling and Constant 
or Variable speed fan systems.

Compatible with most Off the shelf 1 or 2 
stage Conventional Heat/Cool or Heat 
Pump Thermostats. All Mechanical, 
Digital/Electronic, Dual Mode, and Internet 
Compatible Thermostats that operate on 
24vac. Battery powered or Power robbing 
thermostats that draw less than 20 ma of 
current are also compatible. Zone 1 will 
accept One Zone Mode, Carbon Dioxide 
Safety and Auxiliary/Dehumidify mode 
inputs. See pages 9-11 & 14-17  for details.

The UZC4 Zone system features 
automatic changeover from any 
thermostat allowing for individual zone 
comfort from the HVAC system.

The STATUS LED pulses as a steady 
heart beat to indicate active Micro- 
processor status. 
On board Multi-colored LED’s will 
illuminate to indicate system status, 
HVAC system mode,  and active / inactive 
zone identification.     

See page 22 for details

.

Damper 1 thru Damper 22 green LEDs 
will indicate which zone dampers are 
demanded to energize Open or Closed.

The main UZC4 module has a Manual 
Reset circuit breaker with a Ground 
Fault Indicator that protects all 
connected modules and thermostat 
circuitry. All modules have separate 
damper motor Thermal Breakers too. 
They protect the damper motor circuitry 
from shorts in the field wiring. The 
breakers will not protect against shorts 
in the HVAC system wiring. 

CAUTION: 

When the thermal 

breaker is tripped it will get quite 
hot. To reset the breaker: 

Shut off 

power to the panel. Find and repair 
the short. Restore the 24VAC power. 

TEMPERATURE:

 -20° to 160°F (-29° to 71°C)

HUMIDITY: 

0% - 95% RH Non-Condensing.

The UZC4 allows constant operation of 
the Indoor Fan by Thermostat #1 only, or 
by each individual thermostat. When 
controlled by thermostat #1, All Zone 
dampers will respond. When controlled 
individually, Zones not calling  for 
continuous   fan will close. 

Zone 
Capacity

Compatible
HVAC 
Systems

Compatible
Thermostats

Automatic
Heat/Cool
Changeover

Status LED

System LEDs

Damper LEDs

Operating 
Power

Manual
and
Automatic
Thermal
Circuit
Breakers

Operating
Conditions

Indoor Fan
Control

Model UZC4 Zone Control

  

              

TB-221

Box Contents

* UZC4 Zone Control Panel
* Supply Air Sensor
* Technical Bulletin TB221
* Mounting Hardware

Leave this bulletin on the job site for future reference!

EWC Controls Inc.   385 Highway 33    Englishtown, NJ 07726   800-446-3110   FAX 732-446-5362      E-Mail- [email protected]

1

P/N 090375A0221           Revision S  09.04.12

Copyright 

©

 2004 EWC Controls Inc., All Rights Reserved

FA
FA

24V
24V

TB1

R
C

JMP1

C1

D1

RESET

CB1

F1

K1

TB2

MXR
MXC
M6
M4
M2
M1

TB3

4

Z

O
N

E

K2

M6
M4
M2
M1

2

3

M6
M4
M2
M1

Z

O
N

E

Z

O
N

E

TB4

TB5

K3

K4

M6
M4
M2
M1

M6
M4
M2
M1

Z

O
N

E

O
A

D
M
P
R

TB6

1

K5

TB7

K7

M6
M4
M2
M1

NC
NO

C

E
B
D

TB8

K8

K9

G
Y2
Y1
O
B
W1
W2
E
RC
RH

RC
LINK

RH

H
V
A
C

S
Y
S
T
E

M

TB9

K10

K11

K12

K13

JMP3

K14

C

W

E

CONTROLS 

INC.

Englishtown, 

NJ

     HVAC ZONE 
CONTROl SYSTEM 

UZC4

SAS
SAS
OAS
OAS
RAS
RAS

S
E
N
S

O
R

S

TB11

TB10

T
S
T
A
T
4

C
W1 
W2

Y1
Y2
R
G

B

E

C
W1 
W2

Y1
Y2
R
G

B

E

TB12

T
S
T
A
T
3

C
W1 
W2

Y1
Y2
R
G

B

E

T
S
T
A
T
2

TB13

C
W1
W2

Y1
Y2
R
G

B

E

T
S
T
A
T
1

TB14

CO
CO

ONE

ZONE
AUX R

TB15

2

2

EMERGENCY

NORMAL

RAS

SAS

OAS

STATUS

LIMIT

LIMIT

LIMIT

ZONE

ZONE

ZONE

ZONE

OPEN

OPEN

OPEN

OPEN

3

1

2

4

OPEN

OA DMPR

DMPR

BYPASS

AUX RELAY

FAN

COMPRESSOR1

COMPRESSOR2

EMERGENCY

          W2 HEAT

VALVE

REV

          W1 HEAT

LED12

LED13

LED14

LED15

LED16

LED17

LED9

LED10

LED18

LED2

LED3

LED11

LED4

LED1

LED6

LED5

LED7

LED8

RESET

CPU

TIMER

RESET

OFF

SAS

ON

<

>

GAS

FAN

HYDRO

<

>

90

PURGE

180

s

s

<

>

OAS

STAGES

TMR

<

>

DF

HP

CONV

<

>

HP

GAS

SYSTEM

>

>

OFF

FAN PRG

ON

<

>

OFF

%

50

ON

<

>

RA

< AUX RLY>

DA

ANY

< FAN CTRL>

Z

1

OFF

< ZDL >

ON

OFF

< RAS>

ON

0

RA LMT

+10

>

<

HC

HP

> TSTAT>

O

< RV>

B

1

2

CS#

>

<

BANK1

BANK2

R1

STAGING

TIMER

OAS

7

OFF

14

21

28

35

42

37

34

40

43

46

49

52

R2

COOLING

LIMIT

1ST

R3

LIMIT

STAGE

HEATING

DIFFERENTIAL

MULTI

STAGE

HEAT

R4

J1

120

110

130

140

150

160

170

12

19

26

33

40

47

5

D6

D5

D4

R7

R6

R5

D3

JMP2

D10

D7

D8

D9

R10

R11

R9

R8

D14

D13

D12

D11

R15

R12

R13

R14

D16

D15

R17

R16

R18

R63

R55

R53

R52

R54

R61

R60

Z1

R56

R57

R1

9

C2

C54

D2

R2

0

R2

1

R2

2

A
U
X
R
L
Y

C25

C26

C27

R65

R66

R67

R68

R71

R70

R69

R72

R73

R28

R27

R26

R25

R24

R23

D17
D18
D19
D20
D21
D22

R64

C48

C47

C46

C51

C50

C49

C52

SW3

R134

R128

R129

R130

R130

R132

R133

R135

R127

R126

R125

R124

R123

R122

U17

U18

U19

C42

C41

C40

C45

C44

C43

R121

R120

R119

R118

R117

R116

R115

R114

R113

R112

R111

R110

R109

R108

R107

R106

D23

C3

R29
R30
R31
R32
R33
R34
R35
R36

R37
R38
R39
R40
R41
R42
R43
R44

R46

R45

R50

C28

C29

C30

C31

C32

C33

C5

C4

U2

U3

U4

R74

R75

R76

R77

R78

R79

R88

R87

R86

R85

R84

R83

R82

R81

R80

C34

C35

C36

C16

C6

C20

U6

U7

U5

R98

R97

R96

R95

R93

R94

R92

R91

R90

R89

C39

C38

C37

C23

C24

U8

U9

R105

R104

R103

R102

R101

R100

R99

J2

C8

C7

C1

0

C9

C1

1

C1

2

C1

3

C1

4

C1

5

U15

U14

R47

C17

C21

C2

2

C1

9

U1

Y1

SW2

SW1

R51

R50

R48

R4

9

R58

C18

Figure 1.

LED19

GROUND FAULT

C53

INPUT VOLTAGE:

 19-30VAC 60 Hz

Transformer 40-100VA MAX. NEC Class 

2.

CURRENT DRAW:

 Max 22VA @ 24VAC.

OVER-CURRENT PROTECTION:

 4.0

amp or 100VA.

Forced   Air   Zone   Controls

®

Содержание Ultra-Zone UZC4

























Отзывы: