background image

EVS Broadcast Equipment SA 

 

 

11 

PLL_set_B 

The GDR416 is capable of re-clocking a range of 3Gbit/s, HD and 
SD SDI transport stream bitrates. 

PLL_Set_B

 is used to set input 

B of the GDR416 to the correct bitrate of the incoming signal. 

PLL_Set_B

 can be set to 

Auto

270 Mb/s

1485 Mb/s

 and 

2970 Mb/s

. The default setting is 

Auto

Reclocker_B 

The setting item 

Reclock_B

 determines if the incoming signal on 

input B will be reclocked by the GDR416. The settings are: 

 

Auto

: Auto selection between 

Bypass

 and 

Reclocked

.  

 

Bypass

: Does not re-clock the incoming signal 

 

On

: The GDR416 always attempts to re-clock the input 

The default setting is 

Auto

 

 

Mute_B 

Mute_B

 enables input B of the GDR416 to be muted. The settings 

of 

Mute_B

 are 

On

Off

Input Loss

 or 

PLL Unlock

. Set to 

Input Loss

 will mute input B only in case a carrier loss is 

detected on input B. Set to 

PLL unlock

 will mute input B in case 

the PLL rate of input B is not available. The Default setting is 

Off

 

 

PLL_set_C 

The GDR416 is capable of re-clocking a range of 3Gbit/s, HD and 
SD SDI transport stream bitrates. 

PLL_Set_C

 is used to set input 

C of the GDR416 to the correct bitrate of the incoming signal. 

PLL_Set_C

 can be set to 

Auto

270 Mb/s

1485 Mb/s

 and 

2970 Mb/s

. The default setting is 

Auto

 

 

Reclocker_C 

The setting item 

Reclock_C

 determines if the incoming signal on 

input C will be reclocked by the GDR416. The settings are: 

 

Auto

: Auto selection between 

Bypass

 and 

Reclocked

.  

 

Bypass

: Does not re-clock the incoming signal 

 

On

: The GDR416 always attempts to re-clock the input 

The default setting is 

Auto

 

 

Mute_C 

Mute_C

 enables input C of the GDR416 to be muted. The settings 

of 

Mute_C

 are 

On

Off

Input Loss

 or 

PLL Unlock

. Set to 

Input Loss

 will mute input C only in case a carrier loss is 

detected on input C. Set to 

PLL unlock

 will mute input C in case 

the PLL rate of input C is not available. The Default setting is 

Off

 

 

PLL_set_D 

The GDR416 is capable of re-clocking a range of 3Gbit/s, HD and 
SD SDI transport stream bitrates. 

PLL_Set_D

 is used to set input 

D of the GDR416 to the correct bitrate of the incoming signal. 

PLL_Set_D

 can be set to 

Auto

270 Mb/s

1485 Mb/s

 and 

2970 Mb/s

. The default setting is 

Auto

Содержание SYNAPSE GDR416

























Отзывы: