40
WT.050.700.000.DE.IM.0319
Interfaces
DEPOLOX
®
400 M
4.
The Ethernet connection is designed in accordance with IEEE 802.3.
There are two I8P8C sockets (often referred to as RJ45 sockets)
installed. Connection to the HUB or switch can be realized with a 1:1-wire
and screened patch cable. Direct connection to a PC network card is pos
-
sible using a patch cable (1:1) or a crossover cable (crossed network
cable). The LEDs are fitted in the 8P8C socket. They display the interface
statuses. The meaning of the LEDS is as follows:
The connection runs in Auto negotiation mode. The data transfer rate and
full or half duplex are defined automatically with the connected switch/
HUB. The adjacent drawing shows the RJ45 terminal assignment.
4.3.1
Configuring the Ethernet connection for installation in a
network
The electronic module is delivered with a fixed IP address, i.e. the device
can only be addressed via a fixed IP address. Alternatively, the electronic
module can be configured with DHCP.
The Ethernet settings of the electronic module can be configured via the
menu “Settings”–”Network”. The customer-specific IP address and the
subnet mask can be entered. To do so, contact the network administrator
if the electronic module is being integrated into a network. The MAC
address is displayed in the “Information” menu. An Ethernet connection
line to a PC or laptop computer must be installed for data visualization via
Internet browser and an Internet-capable device.
A network connection is set up between a PC or laptop computer with
Ethernet interface (10/100 MB/sec) and the electronic module. In order
to operate the electronic module in a network, the network configuration
must be adapted to the existing network. If required, you can obtain the
necessary information (IP address, subnet mask) from your local network
administrator. You can configure the IP address and subnet mask
assigned to you in the menu “Settings” - “Network.”
Example:
Proceed as follows to visualize the web view of the electronic module in
the browser:
6
Start the browser, e.g. Firefox or Internet Explorer.
LED
(green)
LED
(yellow)
Green: lights up
Ethernet connection established
Green: flashes
Data being transferred
Yellow: off
10 Base-T
Yellow: lights up
100 Base-T
IP address
192.168.200.11 (factory setting)
Network mask
255.255.255.0 (factory setting)
Gateway
0.0.0.0 (factory setting)
Содержание WALLACE & TIERNAN DEPOLOX 400 M
