evoheat FORCE 14 Скачать руководство пользователя страница 7

Страница: 7 / 30

From pump

PVC Coupler

Recommended (Provided)

To pool

Condensation Drain

Barb FTG

2500mm

Air outlet

Air inlet

500mm

700mm

300mm

700mm

1000mm

800mm

Air inlet

Air outlet

2000mm

Correct installation is required to ensure safe and efficient operation of your pool heater.

Installation requirements for EVOHEAT heat pumps include the following:

Appropriate site location and clearances.

Sufficient air ventilation.

Correct electrical connection.

Adequate water flow.

This manual provides the information needed to meet these requirements.
Review all application and installation procedures completely before

continuing the installation.

3.2 Location

Evo recommend the heat pump should ONLY be installed in an outdoor location with

appropriate ventilation.

In the event that a suitable outdoor location is unavailable contact Evo Industries for

specialist technical advice.

If installing the heater on an existing pump/filtration system the heater must be installed

AFTER the filter and BEFORE the chlorinator/sanitizer.

The heat pump should be installed on a flat level surface as close as possible to the pool.

Large runs of uninsulated piping can significantly contribute to heat loss. A rough estimate

of heat loss over a 30m pipe run can be as high as 600 Watts per hour per 5 degrees of

temperature difference between the air/ground and the pool water. These losses need to

be taken into account over long distances and piping may need to be insulated to reduce

heat leakage.

The heat pump should be installed a maximum of

m below the water level of the pool/spa.

Make sure the heat pump is not located where large amounts of water may run-off from a

roof into the unit. Sharp sloping roofs without gutters will allow excessive amounts of rain

water mixed with debris from the roof to be forced through the unit. A water deflector may

be needed to protect the heat pump.

3.3 Clearances

The unit needs continuous fresh

air whilst running. The heater

draws up to 80m3/min ambient air

through the sides and discharges

through the top fan cowl. Leave

sufficient space for unobstructed

airflow into and out of the heater.

Do not locate the heater in an

enclosed area, or the discharged

cold air will recirculate into the

unit and consequently lower the

heating efficiency.

3.4 Water Flow and

Plumbing Setup

All EVOHEAT heat pumps have a

factory preset internal water flow

switch. If there is insufficient water

flow the heater will not operate.

Before connecting the heater

to the plumbing, all piping must

be thoroughly flushed to ensure

no debris can enter the heater.

Failure to remove pipe debris

can jam or damage the flow

switch and may cause damage

to the heater.

When cleaning the pool it is

advisable to turn off your heater

as restricted water flow may

cause the heater to shut down

and indicate low water flow fault

(P08 error).

Minimum required clearances

A Variable speed pump or bypass valve and plumbing MUST be fitted to allow

water flow to be adjusted through the heater. Do not direct connect a water

pump with higher flow than required to the heat pump.

Содержание FORCE 14































Результаты поиска

Содержание FORCE 14

Отзывы:

Бренды по названию

Популярные бренды

evoheat FORCE 14, Руководство по установке и эксплуатации

Результаты поиска

Содержание FORCE 14

Отзывы:

Бренды по названию

Популярные бренды