background image

46

INSTALLATION AND PREDELIVERY

OUTBOARD INSTALLATION

OUTBOARD 
INSTALLATION

Hull Preparation

Maximum Capacity

Before installing outboard:

Refer to the boat manufacturer's certification
label for maximum horsepower rating.

Refer to ABYC Standards to determine the
maximum horsepower capacity for boats with-

out certification labeling.

Mounting Surface

Inspect transom surface prior to drilling mounting
holes.

The transom should meet ABYC Standards.

The transom must be flat and cannot have any
protrusions.

The transom angle should be approximately 14
degrees.

Check transom strength and height.

Top Edge of Transom or Bracket

Transom thickness or off-sets must also be con-
sidered. The top edge of the transom or bracket
must provide a proper surface for stern brackets.
The stern brackets must contact the flat surface of
the transom or bracket. Modify moldings or com-
ponents that prevent the stern brackets from rest-
ing against the transom surface. Do not modify
transom brackets.

Transom Clearances

Make sure the transom and splash well area pro-
vide adequate clearances.

The top edge of the transom should be wide
enough to allow full steering travel. The ABYC

standard for most single outboard installations

is 33 in. (84 cm).

Check cable and hose routing clearances.

Make sure there is clearance for mounting bolts
and washers. Check the inside area of the tran-

som for obstructions prior to drilling holes.

Water Flow

Inspect the hull area directly in front of the mount-
ing location.

Boat-mounted equipment should not create tur-
bulence in the water flow directly in front of the

outboard's gearcase. Turbulence or disruptions

in the water flow directly in front of the gearcase

will affect engine cooling and propeller perfor-

mance.

Avoid locating outboard centerlines within 3 in.
(76 mm) of bottom strakes on dual-outboard

installations. 

WARNING

Do not overpower the boat by installing an
outboard that exceeds the horsepower
indicated on the boat’s capacity plate.
Overpowering could result in loss of con-
trol.

1029A

WARNING

DO NOT install an outboard on a curved or
irregular surface. Doing so can wear, bind,
and damage components, causing loss of
control.

Содержание E-tec 75 HP

























































































































































































































































































































































Отзывы: