Evil Mad Science Meggy Jr RGB Скачать руководство пользователя страница 16

Страница: 16 / 19

[Meggy Jr RGB]

[16]

STEP 14: Button Caps & Rubber Feet

Parts

#23

are molded button key caps

These six button caps

snap

onto the large tactile button switches.

First, add the four square button caps (angled at 45°) on the left hand

side, and then snap the two round ones onto the right-hand buttons.
(If necessary for some reason, the caps can be removed by gently

prying them off with a small flathead screwdriver.)

Part

#25

is a hard urethane rubber foot

Install these four clear rubber bumpers to the bottom of the

circuit board, on flat parts of the board close to the four screw

hole locations. Suggested locations are shown in circles.

Meggy Jr RGB is designed to be mounted and used inside a handle set (case)

that protects the circuit board from your fingers, and protects your fingers from

the circuit board. Parts #25-27 are mounting hardware for attaching these

handles.

Templates to make your own handle sets are available to download at:

http://www.evilmadscientist.com/go/meggyjr

Good news!

The electronics part of the project is now...

done

At this point you can, if you like, put batteries in the battery box,

switch it on, and make sure that everything is working correctly.

(Please make sure the circuit board is resting on a nonconductive

surface when you apply power.)

Screw hole locations

(arrows)

Содержание Meggy Jr RGB




















Результаты поиска

Содержание Meggy Jr RGB

Отзывы:

Бренды по названию

Популярные бренды

Evil Mad Science Meggy Jr RGB, Руководство пользователя

Результаты поиска

Содержание Meggy Jr RGB

Отзывы:

Бренды по названию

Популярные бренды