evertz VistaLINK 7700 MultiFrame Скачать руководство пользователя страница 16

Страница: 16 / 22

7700 MultiFrame Manual

7707OO-2-OC Telecom and Datacom Optical Wavelength Converter

Page-12

Revision

1.3

4.2.3. Displaying the Data Standard Detected at the EQUIPMENT Input

To display the data standard detected at the EQUIPMENT input, select the

STAT

menu item in menu level

1, then use the toggle switch to display the

EQUP

option

and press the pushbutton to select it. Use the

toggle switch to then display the

RATE

option

and press the pushbutton to select it.

STAT

EQUP

RATE

RATES PER MODE
BYP
LOS

Rates per mode:

OC48-2488MBPS

OC48/STM16, 2.488 Gb/s

OC12-622MBPS

OC-12/STM-4, 622 Mb/s

OC3-155MBPS

OC-3/STM-1, 155 Mb/s

ETH-1250MBPS

Gigabit Ethernet

FC-2125MBPS

Fiber Channel, 2.125 Gb/s

FC-1062MBPS

Fiber Channel, 1.062 Gb/s

FC-531MBPS

Fiber Channel, 531 Mb/s

FC-266MBPS

Fiber Channel, 266 Mb/s

FC-133MBPS

Fiber Channel, 133 Mb/s

ETH-125MBPS

Fast Ethernet

XAUI-3125MBPS

XAUI 3.125 Gb/s

XAUI-3187MBPS

XAUI 3.187 Mb/s

ESCON-200MBPS

ESCON

BYP

EQUIPMENT input is set to bypass (non-reclock) mode

LOS

No signal present

4.2.4. Displaying the Optical Power at the EQUIPMENT Input

The 7707OO-2-OC module can measure and display the input optical power over a range of -1dBm to
–40dBm at increments of 1dBm. To display the optical power detected at the EQUIPMENT input, select
the

STAT

menu item in menu level 1, then use the toggle switch to display the

EQUP

option

and press the

pushbutton to select it. Use the toggle switch to then display the

PWR

option

and press the pushbutton to

select it.

STAT

EQUP

PWR

OVER
-1 TO -40
LOW

OVER

Indicates optical input power exceeding –1dBm

-1 to –40

Optical input power within this range

LOW

Input optical power low (< -40 dBm)

4.2.5. Displaying the Firmware Version

To display the version of the 7707OO-2-OC’s embedded firmware, select the

STAT

menu item in menu

level 1, then use the toggle switch to display the

VER

option

and press the pushbutton to select it. The

display will show the following:

VER x.x BUILD xxx

Software version. Character string scrolls across four digit display.

Содержание VistaLINK 7700 MultiFrame























Результаты поиска

Содержание VistaLINK 7700 MultiFrame

Отзывы:

Похожие инструкции для VistaLINK 7700 MultiFrame

Бренды по названию

Популярные бренды

evertz VistaLINK 7700 MultiFrame, Руководство пользователя

Результаты поиска

Содержание VistaLINK 7700 MultiFrame

Отзывы:

Похожие инструкции для VistaLINK 7700 MultiFrame

Бренды по названию

Популярные бренды