background image

 

 

INFORMATION TO USERS IN EUROPE 

 

NOTE 

 

This equipment with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low 

Voltage Directive (73/23/EEC) issued by the Commission of the European Community. 

 

Compliance with these directives implies conformity to the following European standards: 

 

  EN60065 

Product Safety 

  EN55103-1  Electromagnetic Interference Class A (Emission) 

  EN55103-2  Electromagnetic Susceptibility (Immunity) 

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 

to the European Union EMC directive.  These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a commercial environment.  This equipment 

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance 

with the instruction manual, may cause harmful interference to radio communications.  Operation of this 

equipment in a residential area is likely to cause harmful interference in which case the user will be 

required to correct the interference at his own expense. 

 

 

 

 

 

INFORMATION TO USERS IN THE U.S.A. 

 

NOTE 

 

FCC CLASS A DIGITAL DEVICE OR PERIPHERAL 

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 

to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful 

interference when the equipment is operated in a commercial environment.  This equipment generates, 

uses,  and can radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications.  Operation of this 

equipment in a residential area is likely to cause harmful interference in which case the user will be 

required to correct the interference at his own expense. 

 

WARNING 

 

Changes or modifications not expressly approved by Evertz Microsystems Ltd. Could void the user’s 

authority to operate the equipment. 

 

Use of unshielded plugs or cables may cause radiation interference.  Properly shielded interface cables 

with the shield connected to the chassis ground of the device must be used. 

Содержание 570DSK-25G Series

























































Отзывы: