Evers BPT-L19 Скачать руководство пользователя страница 24

Страница: 24 / 41

Preventive maintenance work (wear parts)

WARNING

Unexpected startup during maintenance work, injuries possible.

Always remove the battery before performing cleaning or preventive and corrective maintenance

work

For preventive maintenance work, see also operating instructions (Manual), chapters 6.2 to 6.5.

4.1

Re-greasing the tool

To ensure optimal stability it is recommended that the tool be re-greased regularly.

►

Remove battery from tool.

►

Loosen two cylinder head screws ((# 124) and remove

the front cover ((# 253).

►

Loosen three cylinder head screws (Torx) ((# 124) and

carefully remove clincher housing with guide plate.
– The jaw mechanism, which is only held in position

by grease, is now open for re-greasing.

►

Spray all joints and sliding points at the lubrication

points (

●

) with high-pressure resistant adhesive lubri-

cating oil spray (e.g. Würth HHS 2000)

►

Fitting is performed in reverse order.

4.2

Cleaning/replacing the tension wheel

Dismantling

►

Remove battery from tool.

►

Loosen two cylinder head screws (# 124).

►

Loosen cylinder head screw Torx (# 95) and remove

side cover (# 256) and strap guide (# 258).

►

Loosen two cylinder head screw (# 124) and carefully

pull the support plate off the expansion shaft.

►

Carefully pull out the spacer disk (# 117) and the tensi-

on wheel (# 116).
– The rear shim remains on the expansion shaft.

WARNING

Wear eye protection when cleaning

with

compressed

air!

►

Clean tension wheel (# 116) with compressed air.

►

In the case of heavy soiling of the toothing: Carefully

clean tension wheel with wire brush.

►

Check tension wheel for worn teeth. If teeth are worn,

replace tension wheel.

Attention

The tension wheel must not be cleaned while it is rotating. Risk of tooth breakage!

Fitting

►

Fitting is performed in reverse order. Observe the installation direction of the tension wheel, see arrow on the

outside of the tension wheel.

►

Lightly lubricate the inner diameter of the tension wheel with universal grease (e.g. Klüber grease GBU Y 131,

Microlube).

124

253

124

117

116

258

256

●

Lubricating points

Evers GmbH Graf-Zeppelin-Str. 10 46149 Oberhausen T49 208 99475-0 T49 208 99475-31 [email protected] eversgmbh.de

Содержание BPT-L19










































Результаты поиска

Содержание BPT-L19

Отзывы:

Бренды по названию

Популярные бренды

Evers BPT-L19, Руководство по обслуживанию

Результаты поиска

Содержание BPT-L19

Отзывы:

Бренды по названию

Популярные бренды