GB - 8
When making adjustments while the engine is running such
as carburetor and motion control linkage adjustments, stand
to either side of the tractor and mower and keep clear of
moving or rotating components.
Allow the EverRide mower time to cool before touching the
engine, muffler, or any other part which may be hot.
Always stop the power unit, turn off PTO and allow unit to
cool before refueling.
Keep the engine free of grass, leaves, grease and other
debris which could catch fire.
Keep all hardware tight to ensure the machine is in a safe
working condition. Check the blade mounting nuts often to
make sure they are tight.
Perform only maintenance instructions described in this
manual. Unauthorized maintenance operations or machine
modifications may result in unsafe operating conditions.
For engine maintenance, follow the engine manufacturer’s
recommendations as noted in the engine manual.
Fuel System
Handle gasoline with care. Gasoline is extremely flammable
and its vapors can be explosive.
Use an approved fuel container.
Never add fuel to the mower while the engine is running or
while it is hot. Allow the engine to cool for several minutes
before adding fuel.
Keep matches, cigarettes, cigars, pipes, open flames, or
sparks away from the fuel tank and fuel container.
Always fill the fuel tanks outside using caution. Fill the tank
until the fuel is about one inch from the top of the tank. Use a
funnel or spout to prevent spilling. When refueling at a gas
pump, always ensure the nozzle contacts the neck of the
tank while filling.
Replace the machine and container caps and clean up any
spilled fuel before starting the engine.
Keep the mower and all fuel containers in a safe locked
place to keep children from tampering with them.
Fuel system components rely upon clean fuel for lubrication
and optimum performance. Extreme care must be taken to
prevent ingress of dirt and moisture to prevent damage.
Use only nonmetal portable fuel containers approved by the
Underwriter’s Laboratory (U.L.) or the American Society for
Testing and Materials (ASTM). If using a funnel, make sure it
is plastic.
When practical, do not fuel the equipment on truck beds or
on trailers. Remove them and fuel on the ground. If this is
not possible, use a portable nonmetal fuel container to fill the
equipment.
Hydraulic System
Make sure all hydraulic fluid, hoses, and lines are in good
condition and all lines and fittings are tight before applying
pressure to the hydraulic system.
Check hydraulic connections frequently. They can leak as a
result of damage, as a result of vibration or because they
have worked loose.
Relieve all pressures before disconnecting hoses or lines.
Escaping oil under pressure can cause serious injury.
Escaping hydraulic fluid under pressure can have sufficient
force to penetrate the skin, causing serious injury. Before
applying pressure to the system, make sure all connections
are tightened, and lines, pipes and hoses are not damaged.
Fluid escaping from pinholes may be invisible. Do not use
your hands to search for suspected leaks. Instead, use a
piece of cardboard and wear protective eye wear such as
safety goggles.
If injured by escaping fluid, see a medical doctor at once.
Serious infection or reaction will result if proper medical
treatment is not administered immediately. This fluid can
produce gangrene or severe allergic reaction.
Battery Maintenance
Use caution when charging the battery or performing
maintenance on the battery and electrical system.
Use a voltmeter to check the state of the charge.
If using a battery charger make sure it is unplugged before
connecting or disconnecting the cables to the battery.
Batteries contain sulfuric acid electrolyte. Always wear
protective clothing and eye protection when servicing.
In case of electrolyte contact, rinse area with plenty of water
and seek medical attention.
Make sure the battery is charged in a well-ventilated location
so hydrogen gases that are produced while it is charging can
dissipate. Halt charging if battery exceeds 52°C (125°F).
Keep sparks, flames, and smoking material away from the
battery at all times. To avoid sparks, use care when
removing battery cables from their posts.
Disconnect the battery’s ground cable before working on or
near any electrical parts.
Tire Maintenance
Always ensure the tires are inflated to the correct pressure.
Do not inflate the tires above the recommended pressure.
Make sure all hardware, especially the wheel nuts and bolts
have been tightened to the correct torque.
When removing a tire from the power unit, it is necessary to
support it with blocks or stands, not a hydraulic jack.
CAUTION: Separation of a tire and rim can
cause an explosion that could cause serious
injury or death.
Check the tires for low pressure, cuts, bubbles,
damaged rims, or missing lug bolts and nuts.
Always use a clip-on chuck with an extension
long enough to allow you to stand on one side
of the wheel while inflating the tires. Do not
stand directly in front of the tire while inflating.
Never weld or heat a tire and wheel assembly.
The heat can cause the air inside of the tire to
expand and result in a tire explosion. Welding
also can structurally weaken or deform the
wheel.
Содержание EWRKW2754S
Страница 35: ...GB 35 NOTES...
