background image

Flushing and Draining:

To flush or to drain the Everlast™ Series 2000 water heater, power must be 

turned off and then turn off the cold water supply to the water heater.  The 

lever on the pressure and temperature relief valve should be opened but 

care should be taken so the lever does not snap back as it could damage the 

valve seat.  The pressure in the water heater will be released when the lever 

is opened.
The union at the cold water inlet to the water heater should be undone and a 

hose should be attached to the water heater side of the union. The other end 

of the hose should go to a drain.
Installations including a drain cock, as shown in inlet piping schedule, are 

recommended as this allows for draining and for periodic flushing of the 

water heater without piping disconnection at unions, and without the need for 

rechecking for leaks after reconnection.
Opening the pressure and temperature relief valve allows air into the water 

heater and for the water to drain. Following complete draining of the water 

heater, the closest hot water taps may be opened fully and the pressure and 

temperature relief valve closed with care. The cold water inlet stop valve 

is now opened fully and the water heater may be filled with cold water and 

flushed through to ensure the cylinder contains no sediment and is clean. 

Finally the closest hot taps are closed and power may be turned on again 

tothe completely filled water heater.

4          Warranty Conditions

1. 

The system must be installed by a licensed plumber and/or  

 

electrician in accordance with Everlast™ installation  

  

instructions; and all relevant statutory and local requirements of

 

the State or Territory in which the system is installed.

 

2.    The Everlast™ Series 2000 water heater must be operated and 

 

maintained in accordance with instructions supplied by  

 Everlast™.

 

3.  

This warranty only applies to the water heater product and does not

 

apply to any additional electrical and/or plumbing parts  

 

supplied by the installer.

 

4.  

The system is covered for the indicated period from the date of the

 

original purchase. Should a part of the complete water  

 

heater component be replaced during this period, only the  

 

balance of the original warranty will continue to remain effective.

 

Proof of purchase is required.

 

EVERLAST MANUAL 16pp.indd   11

9/07/10   11:02 AM

Содержание series 2000

















Отзывы: