SURFACE MOUNT INSTALLATIONS
1. Remove retainer screw from right side of the sign. Rem
4. A
and for 277V, use red/orange and white wires. WARNI
(provided) or other approved methods.
5. Push wire connections into the J-box.
6. Mount sign equipment securely in place on the wall. Tw
at the top of the unit housing in addition to the j-box mo
7. Carefully replace the glass into the sign frame channel
8. Connect battery in unit by connecting the Red (+) lead
terminal on the battery and the Black (-) lead from PC
CAUTION: Observe polarity. Failure to connect the bat
unsafe condition. NOTE: Emergency lights will NOT co
9. Replace and secure the front cover.
11. Adjust and focus the lighting heads as required.
CEILING OR LEFT-SIDE END MOUNT
Note: Cannot be right-side end mounted
GENERAL:
1. Remove retainer screw from right side of the sign. Rem
3. Remove both 7/8” DIA KO mounting hole located on the
will be located on top of the frame. For left-side wall mo
side of the frame.
4. Thread 7/8” nuts (2 required, provided by others) onto 7/8” pipe nipples (2 required, provided by others). Slide
pipe nipples through canopy holes.
5. Place screws (provided) in holes on the canopy.
6. Route wires through knockouts in Unit frame (ceiling m
g
(
g
metal mounting plate.
7. Adhering to National, State and Local codes, make wir
and for 277V, use red/orange and white wires. WARNI
(provided) or other approved methods.
8. Push wire connections into the J-box. Secure mounting
9. Secure the canopy to the steel mounting plate with scr
second nut (provided by others) onto each of the pipe
into place. Once canopy is locked into position there w
11. Carefully replace the glass into the sign frame channel
12. Connect battery in unit by connecting the Red (+) lead
on the battery and the Black (-) lead from PC board as
Observe polarity. Failure to connect the battery proper
condition. NOTE: Emergency lights will NOT come ON
g
y g
13. Replace and secure the front cover.
14. Energize the sign fixture with AC supply. The charge in
15. Adjust and focus the lighting heads as required.
This sign may be shipped with an extra face plate and Red lens to make the sign double face. Replace the back
plate with the extra face plate and lens at the start of the installation process, if the application calls for a double
face sign.
move side panel and mounting canopy, set aside.
ing connection. For 120V, use black and white wires
NG: Properly insulate the unused leads with wire nuts
wo additional “Key Hole” mounting holes are located
ounting holes. These two additional mounting slot holes
l and replace end panel and retainer screw.
from the PC board assembly to the positive (+)
board assembly to the negative (-) battery terminal.
ttery properly will result in equipment failure and an
ome ON at this time.
move side panel and mounting canopy, set aside.
frame. For ceiling mount, knock out mounting holes
ount, knock out mounting holes will be located on the
mount) or in EXIT frame (side mount), pipe nuts and
)
(
), p p
ring connection. For 120V, use black and white wires
ING: Properly insulate the unused leads with wire nuts
g plate to J-box (hardware not included).
rews installed in step 5.
nipples on the inside of the housing and lock the canopy
will not be any side-to-side movement on the canopy.
l and replace end panel and retainer screw.
from the PC board assembly to the positive (+) terminal
ssembly to the negative (-) battery terminal. CAUTION:
rly will result in equipment failure and an unsafe
N at this time.
ndicator lights will illuminate.
must be used. Additional chain support may be required by local codes.
wires through 7/8” DIA KO bushing.
10. Energize the sign fixture with AC supply. The charge indicator lights will illuminate
.
10. Place pipe nipples through the mounting holes of the frame until the canopy is touching the frame. Thread a
dhering to National, State and Local codes, make wir
2. Remove retainer screw from the front cover of the unit. Remove the front cover and set aside.
3. Remove 7/8” DIA KO mounting hole located at the top portion of back plate. Use bushings provided to protect
wires from metal edge. Install mounting pan and cable tie to back plate. Secure wires using cable tie. Feed
2. Remove retainer screw from the front cover of the unit. Remove the front cover and set aside.