background image

Warranty 

 

VENDING MACHINE 

36 

6. The warranty is understood as the specialist operations performance by the service, 
appropriate for the removal of the defect covered by the warranty. The warranty repair does 
not cover the operations described in the operation manual as the operations, the user is 
obliged to perform, on his own and on his cost, e.g. replacement of the fuses, verification of 
the proper operation for the devices the product is connected to, maintenance activities etc.   
7. Guarantor will make every effort, to remove the revealed defects within 7 working days 
from the date of receiving the defective product at the service point. Guarantor reserves the 
right to extend abovementioned period in duly justified cases. The user will be informed 
about such case occurrence directly or via the seller service point.  
8. Guarantor reserves the right to charge the entitled to the warranty with the service and 
transport costs, in  case that the revealed defects were not covered by warranty or that the 
product proved to be fully operational.   
9. The following items are not covered by the warranty:  

 

the parts subject to a normal wear, consumables (fuses, springs, drawers etc.), 

 

the defects of the device resulting from the operation failing to comply with the 
operation manual, particularly from improper use, maintenance, service and storage,  

 

the defects resulting from the incorrect electrical installation (on the user side), flooding 
components with water,  

 

the mechanical damages and the defects resulting from that damages,  

 

the defects and damages attributed to force majeure (e.g. lightning, flood, corrosion, 
power-line surges),  

 

the defects resulting from the unauthorized repairs, modifications and design changes 
performer either alone or by unauthorized body,  

 

the activities and parts listed in the operation manual and belonging to the normal 
operation of the device,  

 

the defects resulting from improper device selection,  

 

the defects and malfunction of the device resulting from the device incorrect or faulty 
installation,  

 

the products whose the Warranty Card or serial number have been changed, blurred, 
removed or erased.  

10. Guarantor reserves the right to refuse the complaint acceptance, based on the 
statement of the product incompleteness, unauthorized repairs performance, design 
changes, usage contrary to the intended use or intentional damage.    
11. The matters not regulated in this warranty conditions shall be governed by the Civil 
Code.   
12. In case the buyer is the buyer within the meaning of the trade law, disputes shall be 
settled by the court competent for the place of residence.  
 

 

I declare that I have read  and understood the warranty conditions and all information 
regarding the manner of product use.  

 

Date and legible signature 

 
 
 
 
 
 
 
 
 
 
 
 

Содержание SOLID AS 6x10










































Отзывы: