Evco EV3 CHIL Скачать руководство пользователя страница 29

Страница: 29 / 46

EVCO S.p.A.

EV3 CHIL & EVD CHIL | Installer manual ver. 1.2 | Code 1443DCHILE124

page 29 of 46

M AL10

5 0

255

Flow alarm re-arm delay from deactivating flow switch

input

S AL12

3,0

-127

127

°C

Antifreeze alarm set-point

S AL13

2.0

0.0

25.5

°C

Antifreeze alarm hysteresis

M Al14

- - - -

Stop fan

with antifreeze alarm

0= Disabled

1= Enabled

M Al17

105.0 0.0 255.0 °C

High

discharge

temperature alarm set-point

M AL18

15.0

0.0

25.5

°C

High discharge temperature alarm hysteresis

PARAM.

DEFAULT

MIN.

MAX.

U.M.

COMPRESSOR

CP01

255

s*10

Compressor OFF minimum time

M CP02

255

s*10

Compressor successive switch-ons minimum time

M CP05

CP06

Hz - %

Minimum modulating compressor value

M CP06

100

CP05

255

Hz - %

Maximum modulating compressor value

M CP08

0.0 0.0 25,5 °C

Cut-off hysteresis for modulating compressor adjustment

(“CooL”)

For ON-OFF adjustment set to 0

M CP09

255

Hz - %

Set-point for refreshing the modulating compressor oil

M CP10

255

min

Delay for refreshing the modulating compressor oil

PARAM.

DEFAULT

MIN.

MAX.

U.M.

COMPRESSOR ADJUSTMENT

rL01

5.0

0.0

25.5

°C

Proportional compressor adjustment band

rL04

255

s*10

Compressor adjustment integral time

PARAM.

DEFAULT

MIN.

MAX.

U.M.

VENTILATION

M Fn01 20 0 255 s/10

Fan start-up time, if CF36 is set to 1 (AO2 output

configuration type = phase cutting)

M Fn02

ms/2

Fan phase shift

M Fn03

- - - -

Fan mode

0= On-call (dependant on the compressor)

1= Independent

Содержание EV3 CHIL















































Результаты поиска

Содержание EV3 CHIL

Отзывы:

Evco EV3 CHIL, Руководство по установке, Страница: 29 / 46

Результаты поиска

Содержание EV3 CHIL

Отзывы: