Evco EV3 CHIL Скачать руководство пользователя страница 12

Страница: 12 / 46

EVCO S.p.A.

EV3 CHIL & EVD CHIL | Installer manual ver. 1.2 | Code 1443DCHILE124

page 12 of 46

3.3

Measurements and installation of EV3K01

The pictures below show the measurements of EV3K01; measurements are expressed in mm (inches).

To be installed on a panel with snap-in brackets provided.

The thickness of the panel on which the EV3K01 is to be installed must be between 0.8 and 2.0mm (0.031 and 0.078 in).

3.4

Installation precautions

Ensure that the working conditions for the devices (operating temperatures, humidity, etc.) are within the set limits. See

the section TECHNICAL SPECIFICATIONS.

Do not install the devices close to heat sources (heating elements, hot air ducts, etc.), equipment with a strong magnetic

field (large diffusers, etc.), in places subject to direct sunlight, rain, damp, excessive dust, mechanical vibrations or shocks.

In compliance with safety regulations, the devices must be installed properly to ensure adequate protection from contact

with electrical parts. All protective parts must be fixed in such a way as to need the aid of a tool to remove them.

Содержание EV3 CHIL















































Результаты поиска

Содержание EV3 CHIL

Отзывы:

Похожие инструкции для EV3 CHIL

Бренды по названию

Популярные бренды

Evco EV3 CHIL, Руководство по установке

Результаты поиска

Содержание EV3 CHIL

Отзывы:

Похожие инструкции для EV3 CHIL

Бренды по названию

Популярные бренды