EVBox Elvi Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 38

EVBox Elvi Скачать руководство пользователя страница 20

Single 3-phase 400 V AC 16 or 32 A power cable

4.1.5. Hub-Satellite installations (optional)

A Hub-Satellite charging station installation can consist of up to 10 Satellite charging stations
connected to the Hub station. In any installation there must be one Hub station, and all Satellite

stations connect to that Hub station using wireless RF communication. The Hub-Satellite installation is
set-up using the EVBox Connect app. See

Configure a Hub-Satellite installation on page 24

.

A Hub-Satellite installation is used for the following functions:

• To distribute available power over the charging stations that are being used. For correct load

balancing, a Hub-Satellite configuration must be connected from a single power supply cabinet. If
a group of charging stations is powered from a different power supply cabinet then that group of

stations must be a separate Hub-Satellite configuration.

• Sharing a common Internet connection using either a Wi-Fi connection to a local Wi-Fi router or an

optional SIM to connect through a cellular network.

Note the following when choosing locations for Satellite charging stations:

• All Satellites must be within 100 m (328 ft) of the Hub.
• Obstructions such as walls and floors can decrease the strength of the communication signal.
• If the Satellite is not within range of the Hub, or if the signal strength is too low, then the Satellite

will not appear in the EVBox Connect app.

4.1.6. Smart Charging (optional)

A Smart Charging system to optimize load balancing can be connected to the Hub charging station.
Route a SFTP Category 5 or 6 network cable from the Smart Charging system to the installation area of
the Hub charging station. For outdoor installations, use a UV stabilized network cable. Make sure that

EN

4. Installation instructions

16

«
...
18
19
20
21
22
...
»

Содержание Elvi







































Отзывы:

Нет отзывов