EUTECH INSTRUMENTS alpha pH 200 Скачать руководство пользователя страница 7

Страница: 7 / 40

- 3 -

OVERVIEW

3.1

Front Panel

The front panel consists of a 4-digit LED display, 8 LED annunciators and 4 keys.

Annunciators

1. REL 1

Displayed when Relay 1 is activated

2. REL 2

Displayed when Relay 2 is activated

3. MEAS

Displayed in measurement mode

4. CAL

Displayed in calibration mode

5. SETUP

Displayed in setup mode

6. pH

Unit of the displayed parameter (pH)

Unit of the displayed parameter (temperature)

8. mV

Unit of the displayed parameter (ORP)

Keys

9. MODE

Use to toggle between measurement
modes (pH/ORP and temperature)

10. ENTER

Press to confirm changes or to enter into
further levels of the lower menu

11.

▲

▼

(increment /

decrement)

Use during calibration and setup modes to
increment or decrement . Press both keys
together in calibration and setup modes to
escape to Measurement mode

12. Full 14-segment display

Содержание alpha pH 200









































Результаты поиска

Содержание alpha pH 200

Отзывы:

EUTECH INSTRUMENTS alpha pH 200, Инструкция по эксплуатации, Страница: 7 / 40

Результаты поиска

Содержание alpha pH 200

Отзывы: