Eusso UTG7100-IP Series Скачать руководство пользователя страница 5

Страница: 5 / 48

6. Installations & SIP Configurations

Connect UTG7100-IP RJ45 WAN port to NAT Router using a Category 5 LAN cable.

2. Connect RJ45 LAN port to Notebook PC using a Category 5 LAN cable.
3. Connect DC Power Adaptor. The LCD Panel will start displaying

”

Loading Program

”

for about 5

seconds, and the LEDs will be ON and start initializations.

4. . The LCD panel will show

Date

Time

and

No service

without SIP registration, or

phone number

after successful SIP registration.

5. Pick up the phone, and you will hear a dial tone and the LCD panel will show

IP Dialing.. 1

If you

hear a busy tone, please check if the WAN port is connected and hang up.

6. Press

Menu_7_4

, and

test

(i.e. press

two times_

three times_

five times_

two times_

enter

) to

enter password first. Press

Menu_4_5

from keypad to read WAN and LAN IP addresses. The

default LAN IP address is

192.168.123.1

7. Go to Chapter 8 and you may enter this IP address in IE Web browser for web configurations.

Configure and register UTG7100-IP into your SIP server. There are more details and examples
for VoIP application of SIP registrations in Chapter 10.

8. If UTG7100-IP has successfully registered in the SIP server, the LED

REG

will turn ON.

9. Pick up the phone, and press

123456#

to call the party with the number

123456

registered in the

SIP server. Note that

will dial out the number immediately. Dialing without

will not dial out until

the auto dial timer (default=5 seconds) elapsed. In a moment, you should hear a ring back tone,
and wait for answer.

7. Default Reset by Using Keypads

Press

Menu / 7.Administrator / 3.Default setting / 1.Load default

by using Menu and arrow keys to

reset back to factory defaults, and the LCD panel will show

Set Default….

In 5 seconds, the LCD will

start showing

Loading Program

and

System Initialized

. The UTG7100-IP will reset to default and

restart.

Press

Menu / 7.Administrator / 7.Restart

to reboot UTG7100-IP . In 5 seconds, the LCD will start

showing

Loading Program

and

System Initialized

Содержание UTG7100-IP Series

















































Результаты поиска

Содержание UTG7100-IP Series

Отзывы:

Похожие инструкции для UTG7100-IP Series

Бренды по названию

Популярные бренды

Eusso UTG7100-IP Series, Руководство пользователя

Результаты поиска

Содержание UTG7100-IP Series

Отзывы:

Похожие инструкции для UTG7100-IP Series

Бренды по названию

Популярные бренды