Eurotherm 637+/D6R KD6R Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 87

background image

Product-manual Model: 637+/D6R KD6R

07-02-09-01-E-V0402.doc

47

4

Mechanical installation

4.1

Mounting

Eurotherm digital servo drives may be installed only in a vertical position to guarantee the best air
circulation for the cooling ribs of the heat sink. Vertical installation above other drive racks or above other
heat producing devices can lead to overheating. In addition the drives are to be operated exclusively in
Eurotherm racks or the compact enclosure respectively.

4.2

Control cabinet - mounting

Installation should be carried out only in a control cabinet in which the inside must be free from dust,
corrosive fumes, gases, and all liquids.

Make absolutely sure that the condensing of evaporating liquids including atmospheric moisture, is
avoided. Should the digital servo drive be installed in a place where condensation is likely, a suitable
anticondensation heater must be installed. The heater must be SWITCHED OFF during normal operation.

Automatic switch off is recommended
Eurotherm-digital servo drives should not be installed in are as which have been classified as dangerous, if
they have not been installed in an approved enclosure an accordance with regulations and checked.

Make sure, there is enough cooling and space ! (see sketch)

only horizontal !

on the side
no distance is required

rack

100 mm space

100 mm space

Servo-drives

637+

above

below

General rule

:

It is better to place heat-producing devices low in an enclosure to support internal convection and
to spread the heat. If placing such devices up high is unavoidable, enlarging the upper dimensions
at the expense of height or installing fans should be considered.

4.3

Cooling

The digital servo drives are protected against damages caused by overheating.
There is a thermal sensor installed on the heat sink. When the temperature rises to >95°C,
the drive is automatically switched off. This setting cannot be changed.
Make sure a cabinet of proper size is selected for adequate air circulation

If the device becomes operated in a not ventilated device, the case volume of the specified
control cabinet must be calculated in accordance with the following table !

Gerät

Volumen/Schaltschrank

637+/D6R02...D6R10

0,12 m³

637+/D6R16...D6R30

0,25 m³

For more exact information, please, address to the control-cabinet manufacture

«
...
45
46
47
48
49
...
»

Содержание 637+/D6R KD6R
























































































Отзывы:

Нет отзывов

Похожие инструкции для 637+/D6R KD6R

Бренд: GRASS Страницы: 19

atos E-BM-AC Series

Бренд: Hydro Страницы: 42

Rexroth EFC 3600

Бренд: Bosch Страницы: 238

Rexroth IndraDrive FC Series

Бренд: Bosch Страницы: 72

Rexroth Hagglunds DOb

Бренд: Bosch Страницы: 80

REXROTH IndraDrive

Бренд: Bosch Страницы: 437

Rexroth EcoDrive Cs DKC-004 Series

Бренд: Bosch Страницы: 45

Бренд: Becker Страницы: 28

REVCON DC 13-400-1-0

Бренд: Eltroplan Страницы: 77

Бренд: LinMot Страницы: 23

Бренд: HSB Страницы: 32

Бренд: Danfoss Страницы: 179

VLT 3500 Series

Бренд: Danfoss Страницы: 123

Бренд: SOMFY Страницы: 108

MCA 122 Modbus TCP

Бренд: Danfoss Страницы: 46

Бренд: VAR Страницы: 4

DeviceNet SI-N3

Бренд: YASKAWA Страницы: 76

Бренд: SEW-Eurodrive Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды