Eurotech ZEUS Скачать руководство пользователя страница 36

Страница: 36 / 136

ZEUS Technical Manual

Detailed hardware description

ZEUS Modem-1 supports the following modules:

•

Sony Ericsson GR64, a quad-band (850/900/1800/1900) version of GR47/48.

Functionally comparable to the Sony Ericsson GR47/GR48 devices, the GR64

offers a broad range of voice and data features. The integrated TCP/IP stack

enables effective use of GPRS. For further details see

Sony Ericsson GR64

page

104

•

Siemens MC35i/39i, a dual-band GSM/GPRS module (EGSM 900/1800MHz). For

further details see

Siemens MC35i/39i

, page

106

•

Fastrax iTrax03/8, a 12-channel GPS receiver. iTrax03/8 features low power

consumption, small footprint, 8Mbit internal Flash and does not require battery

backup. For further details see

Fastrax iTrax03/8

, page

108

•

Motorola iO270, a wireless modem that provides packet data, circuit data and

voice connectivity on the iDEN 800MHz network. The iO270 include a GPS

receiver. For further details see

Motorola iO270

, page

110

For further details about this modem see the section

ZEUS Modem-1

, page

118

ZEUS Modem-2 supports the following wireless module with built-in GPS receiver:

•

Telit GE863-GPS module, which supports communication services in quad-band

EGSM 850/900/1800/1900MHz networks. For further details see

Telit GE863-GPS

page

112

For further details about ZEUS Modem-2, see the section

ZEUS Modem-2

, page

118

ZEUS Modem-3 supports the following wireless modules:

•

Sierra Wireless MC8775 PCI Express Mini Card embedded module, which offers

connectivity to all three HSDPA/UMTS frequency bands (850, 1900, 2100 MHz)

and all four EDGE/GPRS bands (850, 900, 1800 and 1900 MHz) used worldwide.

For further details see

Sierra Wireless MC8775

, page

114

•

Sierra Wireless MC5720 PCI Express Mini Card embedded module, which offers

a complete wireless data solution over CDMA 1x EVDO networks with typical

download data rates of 400-700 kbps. For further details see

Sierra Wireless

MC5720

, page

116

•

Fastrax iTrax03/16, a 12-channel GPS receiver. iTrax03/16 features low power

consumption, small footprint, 16Mbit internal Flash and does not require battery

backup. For further details see

Fastrax iTrax03/8

, page

108

For further details about ZEUS Modem-3, see the section

ZEUS Modem-3

, page

119

Содержание ZEUS









































































































































Результаты поиска

Содержание ZEUS

Отзывы:

Похожие инструкции для ZEUS

Бренды по названию

Популярные бренды

Eurotech ZEUS, Техническое руководство

Результаты поиска

Содержание ZEUS

Отзывы:

Похожие инструкции для ZEUS

Бренды по названию

Популярные бренды