Eurotech ZEUS Скачать руководство пользователя страница 34

Страница: 34 / 136

ZEUS Technical Manual

Detailed hardware description

Static RAM

The PXA270 processor provides 256KB of internal memory-mapped SRAM. The

SRAM is divided into four banks, each consisting of 64KB.

The ZEUS also has an external 256KB SRAM device fitted, arranged as 256Kbit x 8-

bits. Access to the device is on 16-bit boundaries, whereby the least significant byte is

the SRAM data and the 8-bits of the most significant byte are ‘don’t care’ bits. The

reason for this is that the PXA270 is not designed to interface to 8-bit peripherals. This

arrangement is summarized in the following data bus table:

Most significant byte

Least significant byte

D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

Don’t Care

SRAM Data

The external SRAM is non-volatile while the on-board coin cell battery is fitted.

Configuration EEPROM

The configuration EEPROM is interfaced directly to PXA270’s I

C controller. It is a

Microchip 24AA01 1Kbit EEPROM organized as one block of 128 x 8-bit memory.

The configuration EEPROM is addressable at I²C serial bus address 0x50 and is

accessed in fast-mode operation at 400KB/s.

Содержание ZEUS









































































































































Результаты поиска

Содержание ZEUS

Отзывы:

Бренды по названию

Популярные бренды

Eurotech ZEUS, Техническое руководство

Результаты поиска

Содержание ZEUS

Отзывы:

Бренды по названию

Популярные бренды